| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 4 that are not LAN technologies?
A.) HDLC
B.) FDDI
C.) 802.5
D.) HSSI
E.) SDLC
F.) Frame Relay | AXA | 1 |
| Which ISDN specification deals with call Setup and Teardown?
A.) Q-Series
B.) J-Series
C.) I- Series
D.) C- Series
E.) F-Series | | 1 |
| Where is the backup configuration file stored?
A.) RAM
B.) ROM
C.) Console
D.) NVRAM | | 1 |
| What is true when using DDR?
A.) HDLC is the preferred encapsulation
B.) You must use static routing
C.) You should use dynamic routing
D.) You should use ISDN | | 1 |
| Identify the command to run 'setup'?
A.) Router(config)#setup
B.) Router?setup
C.) Router#setup
D.) Router>setup | Karrox | 1 |
| Identify the command that disables name-to-address translation?
A.) Router(config-dns)# no ip domain-lookup
B.) Router(config)# no address translation
C.) Router(config)# no ip domain-lookup
D.) Router(config)# ip domain-lookup | | 1 |
| Identify the hardware component that stores the bootstrap
program?
A.) ROM
B.) NVRAM
C.) Booter load
D.) RAM
E.) Flash | | 2 |
| What is proxy-ARP and how it is used and configured | | 1 |
| Describe End to End network services: (Choose all that apply)
A.) Best Route selection
B.) Accomplished Segment by Segment, each segment is autonomous
C.) Flow Control & Data Integrity
D.) Best efforts packet delivery | | 1 |
| What is a characteristic of Store and Forward switches?
A.) They forward the frame before it is completely read.
B.) They work at wire speed.
C.) They are the same a Cut-Through switching.
D.) They read the entire frame and check CRC before forwarding.
E.) They decrease latency. | | 1 |
| Hi Gyes, here is new question. can you provide answer of
following question
Like linux, can we windows as router?
If yes how can we able to do this, | | 2 |
| what is diffrence betwwen mpls and frame really | Volvo | 1 |
| What are the Timer of RIP, IGRP, EIGRP and OSPF Routing
Protocol?
| IBM | 15 |
| Which of the following is an example of the Network Layer?
A.) Token Ring
B.) RARP
C.) LLC
D.) DDP
E.) TCP | | 1 |
| Why Clock rate command is not configured on ethernet
interface of a router? | | 4 |
| Which three devices can be used to convert the user data
from the
DTE into a form acceptable to the WAN service's facility?
A. Modem
B. CSU/DSU
C. TA/NT1
D. CO
E. SS7 | | 1 |
| Which of the following is an example of a Transport Layer
protocol?
Ethernet
IP
TCP
RS-232
| | 1 |
| Which statement is true?
A. While bridges are used to segment networks, they will not
isolate broadcast or multicast packets.
B. A bridge looks at every packet within its network segment
and works like a hub re-broadcasting the packet if the
destination is within its network segment.
C. A bridge maintains a table of the IP addresses of the
hosts within its network segment and forwards the packet
directly to the destination based upon the IP address.
D. A bridge resets the hop count by keeping all packets
within the network segment. Only packets addressed to a
specific destination host outside the network segment are
allowed to pass through the bridge. | | 1 |
| Which protocol will let neighbor routers know if your
internetwork
experienced congestion on a serial port?
A.) BootP
B.) IP
C.) ICMP
D.) ARP
E.) FTP
F.) RARP | | 1 |
| Identify the switching method that receives the entire frame
then
dispatches it?
A.) Cut-through
B.) Receive and forward
C.) Store and forward
D.) Fast forward | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
