| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which command displays the IPX SAP table?
A.) show ipx sap
B.) show sap
C.) show ipx interface
D.) show ipx servers
E.) show ipx | | 1 |
| What is the Network Layer of the OSI responsible for?
A.) Bridging
B.) Routing packets through an internetwork
C.) Regenerating the digital signal
D.) Gateway services | | 1 |
| The Internet Protocol (IP) occurs at what layer of the seven
layer
model?
A.) Physical
B.) Presentation
C.) Network
D.) Datalink
E.) Session
F.) Transport | | 1 |
| As a system administrator, you need to set up one Ethernet
interface on the Cisco router to allow for both sap and
Novell-ether encapsulations. Which set of commands will
accomplish this?
A. interface ethernet 0.1
ipx encapsulation Novell-ether
ipx network 9e
interface ethernet 0.2
ipx network 6c
B. interface ethernet 0
ipx encapsulation Novell-ether
ipx network 9e
interface ethernet 0
ipx encapsulation sap
ipx network 6c
C. interface ethernet 0.1
ipx encapsulation Novell-ether
interface ethernet 0.2
ipx encapsulation sap
D. interface ethernet 0.1
ipx encapsulation Novell-ether
ipx network 9e
interface ethernet 0.2
ipx encapsulation sap
ipx network 6c | | 1 |
| Which service takes information from multiple sources and
allocates bandwidth on a single media?
A. Time-division Multiplexing (TDM)
B. Signaling System 7 (SS7)
C. X.25
D. Frame relay | | 1 |
| Identify the switching method that examines the destination MAC
address as
the frame is being received then begins forwarding the frame
prior to
receiving the entire frame?
A.) Fragment-free
B.) Store and Forward
C.) Cut-through
D.) Fast forward | | 1 |
| Which statement about the data link connection identifier
(DLCI) is true?
A. It is a number that identifies a local virtual circuit in
a Frame Relay network
B. It is a signaling standard between the CIDE device and
the Frame Relay switch
C. It is the clock speed (pod speed) of the connection
(local loop) to the Frame Relay Cloud
D. It is the Maximum number of uncommitted bits that the
Frame Relay switch will attempt to transfer beyond the
Committed Information Rate (CIP) | | 2 |
| A router on one side of a PPP link uses the resonance RTR1
and the password COPP1-PWD. Which configuration line on
RTR1 enables a connection between RTR1 and another router
named RTR2?
A. username, RTR2 password COPR1-PWD,
B. username, RTR1 password COPR1-PWD,
C. username, RTR2 password COPR2-PWD,
D. username, RTR1 password COPR2-PWD, | | 1 |
| What does a Standard IP Access-list use as test criteria?
A.) IP source address
B.) IP source and destination address, protocol numbers and
port numbers
C.) IPX source and destination address
D.) Source MAC address | | 1 |
| Which ISDN protocol prefix specifies switching and signalling?
A.) I
B.) E
C.) Q
D.) S | | 1 |
| Which protocol will send a message to routers if a network
outage or
congestion occurs?
A.) ARP
B.) TCP
C.) IP
D.) ICMP | | 1 |
| What does -1 mean in an extended IPX access-list?
A.) Any IP address
B.) Deny all
C.) Deny host
D.) Any host or any network | | 1 |
| What is the Broadcast IP Address? | | 11 |
| Bridges work at what layer of the OSI model?
A.) Data Link
B.) Network
C.) Physical
D.) Application | | 1 |
| You are a system administrator on a NetWare network, you are
running NetWare 4.11 and you cannot communicate with your
router. What is the likely problem?
A. NetWare 4.11 defaults to 802.2 encapsulation.
B. NetWare 4.11 defaults to 802.3 encapsulation
C. Cisco routers only work with NetWare 3.11.
D. NetWare 3.11 defaults to 802.2 encapsulation. | | 1 |
| What is the meaning of PASSIVE interface in RIP, IGRP, EIGRP
& OSPF??
Can any one explain..!!! | | 4 |
| router | Infotech | 1 |
| Identify the correct pair of Novell Ethernet encapsulation and
Cisco terminology?
A.) Ethernet II, Snap
B.) Ethernet 802.3, Novell-Ether
C.) Ethernet SNAP, Arpa
D.) Ethernet 802.2, Snap | | 1 |
| hi friend i hav difficulty n need to solve it...v need to
implement a new raw switch in company as to increase the no
of staff...snc raw switch by default is in server mode,i
wanna know 1.how to make a switch in client mode...2.how to
configure switch i mean to sy how to connect all switches to
network. | | 1 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
