| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| 3. What does a bridge use to segment a network?
A. IP Addresses
B. Broadcasts
C. Application data
D. Media Access Control addresses
| | 2 |
| If you are running Token Ring with Novell IPX routing, which
encapsulation should you use?
A.) SAP
B.) SNAP
C.) 802.5
D.) 802.2 | | 1 |
| Identify the command to reload the router?
A.) Router(config)# reload
B.) Router# reset
C.) Router# reload
D.) Router> reload | | 1 |
| CSMA/CD stand for which of the following?
A.) Carrier Sense, Multiple Access with Collision Detection
B.) Collision Sense, Multiple Access with Collision Detection
C.) Collision Sense, Multiple Access with Carrier Detection
D.) Carrier Sense, MAC address with Collision Detection | | 3 |
| During encapsulation, in which order is information packaged?
A. Data, Packet, Segment, Frame
B. Segment, Data, Packet, Frame
C. Data, Segment, Packet, Frame
D. Packet, Data, Segment, Frame
E. Frame, Data, Segment, Packet
F. Bread, Peanut Butter, Jelly, Bread | | 2 |
| Which two of the following protocols are used at the
Transport layer?
A.) ARP
B.) UDP
C.) ICMP
D.) RARP
E.) TCP
F.) BootP | | 7 |
| Select the correct statements about PPP and SLIP for WAN
communications?
A. PPP uses its Network Control Programs (NCPs) component to
encapsulate
multiple protocols.
B. PPP can only transport TCP/IP
C. SLIP can only transport TCP/IP.
D. SLIP uses its Network Control Programs (NCPs) component to
encapsulate multiple protocols. | | 1 |
| Identify the purpose of the following command 'ip route
192.168.100.0 255.255.255.0 10.1.0.1'
A.) Enabling a dynamic routing protocol
B.) Creating a static route to the 10.1.0.0 network
C.) Teaches the router about the distant network
192.168.100.0 and how
it can be reached via 10.1.0.1
D.) Assigning the IP address 192.168.100.0 to an interface | | 1 |
| what is hop count? | | 11 |
| The two sublayers of the IEEE Data Link Layer are which of the
following?
A.) Link and Logical Control
B.) Data Link and LLC
C.) Logical Link Control and Media Access Control
D.) Data Link and MAC | | 2 |
| Which ISDN protocol prefix specifies switching and signalling?
A.) I
B.) E
C.) Q
D.) S | | 1 |
| Which OSI layer supports the communication component of an
application?
A.) Data-Link
B.) Physical
C.) Session
D.) Presentation
E.) Application
F.) Transport | | 2 |
| Identify the type of routing protocol that exchanges entire
routing tables at regular intervals?
A.) Link state
B.) Interior gateway protocols
C.) Appletalk routing
D.) Distance vector | | 1 |
| Identify 3 ways in which a router can be configured?
A.) TFTP
B.) Nvram
C.) ROM
D.) Console
E.) Trace | | 1 |
| There are 2 types of PPP authentication supported by the Cisco
IOS. What are they?
A.) PAP
B.) PREDICTOR
C.) MD5
D.) CHAP
E.) STACKER
F.) MSCHAP | | 1 |
| What is the correct command line syntax for configuring a
port on
a 7000 or 7500 series Cisco router with a VIP card?
A.) port
B.) port adapter/port
C.) You can't put a VIP card in a 7000 or 7500 router.
D.) slot/port-adapter/port
E.) slot/port
F.) slot | | 1 |
| When determining whether or not to route a LAN segment,
which rule
of thumb do you use?
A.) 60/40
B.) 50/50
C.) 80/20
D.) 90/10
E.) 70/30 | | 1 |
| Which command loads a new version of the Cisco IOS into a
router?
A. copy flash ftp
B. copy ftp flash
C. copy flash ftp
D. copy tftp flash | | 1 |
| What does the User Datagram Protocol (UDP) provide?
A.) Connectionless datagram service.
B.) FECN & BECN
C.) Flow control and error checking.
D.) Name resolution.
E.) Path discovery. | | 1 |
| In the setup dialog, what do the square brackets indicate?
A. current or default spores
B. hard coded values that cannot be modified
C. values entered by the administrator but not saved
D. values that must be written to PAVRAM before becoming enabled | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
