| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| Your Ethernet interface currently has the IP address of
1.1.1.1/24. You would like it to have a second IP address of
2.2.2.2/24.
Which command will do that?
A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0
B.) ip address 2.2.2.2 255.255.255.0 secondary
C.) ip address 2.2.2.2 255.255.255.0
D.) This cannot be done, you can only have 1 IP address per
physical
interface.
E.) ip address 2.2.2.2 /24 | | 1 |
| the term which used for describe physical alyout of network
mine answer-topology | | 1 |
| What is the distance limitation for 100BaseT?
A. 305.955 ft
B. 7283.46 inches
C. 184 Meters
D. 185 Kilometers | | 3 |
| 1. What is an advantage to LAN segmentation?
A. Provides multiprotocol support
B. Decreases security
C. Decreases broadcasts
D. Increases broadcasts
| | 2 |
| Identify the 3 characteristics of IGRP?
A.) Uses hop count as a metric
B.) Supports multiple unequal paths
C.) Administrative distance is 100
D.) Configured with an Automous system number
E.) Link state | | 1 |
| What is NOT a characteristic of a network segment on a switch?
A. The segment has its own collision domain
B. The segment can translate from one media to a different media
C. All devices in the segment are part of the same broadcast
domain
D. One device per segment can concurrently send frames to
the switch. | jetking | 1 |
| Identify 3 IP applications?
A.) AURP
B.) ARP
C.) Telnet
D.) SMTP
E.) DNS
F.) RARP | | 2 |
| Where is the backup configuration file stored?
A.) RAM
B.) ROM
C.) Console
D.) NVRAM | | 1 |
| Of the following switching types, which one has the highest
latency?
A.) Cut-through
B.) None
C.) Store-and-forward
D.) Fragment Free | | 1 |
| Identify the correct pair of Novell Ethernet encapsulation and
Cisco terminology?
A.) Ethernet II, Snap
B.) Ethernet 802.3, Novell-Ether
C.) Ethernet SNAP, Arpa
D.) Ethernet 802.2, Snap | | 1 |
| Which encapsulation methods are most commonly used with
dialup Integrated Services Digital Network (ISDN)?
A. IP and IPX
B. IP and PPP
C. PPP and SDLC
D. PPP and HDLC | | 1 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| thnx jitender...its me shridh...m working for SG ltd..the
situation iz like ths -at a specific time in our company the
internet connectivity goes off...v hav two networks in our
company...but out of it only one link goes down for 5-10
sec...a fastethernet port becomes down for few sec and
automatically becomes Up... Is this occures becoz of Power??
If yes thn y the 2nd network is not affected??
plz tel me jitender how to resolve ths problem?
as u sd loop in switch is the primary cause of ths....i
wanna know how to resolve it...thnx for ur replys jitender
sinha. | | 2 |
| Which layer is responsible for coordinating communication
between
systems?
A.) Application
B.) Network
C.) Session
D.) Transport
E.) Physical
F.) Data Link | HCL | 2 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 2 |
| What are four ways that Fast Ethernet compares to 10BaseT
Ethernet? (Choose four)
A. Fast Ethernet uses the same Maximum Transmission Unit (MTU)
B. Fast Ethernet is based on an extension to the IEEE 802.3
specification
C. Fast Ethernet uses the same Media Access Control (MAC)
mechanisms
D. Fast Ethernet preserves the frame format that is used by
10BaseT Ethernet
E. Fast Ethernet errors a speed increase one hundred times
that of the 10BaseT Ethernet | | 1 |
| A ISDN PRI circuit can be described as which of the following?
A.) 24 B channels and 1-64Kbps D channel
B.) 23 B channels and 1-64Kbps D channel
C.) 2-D channels and 1-C channel
D.) 2-64Kbps B channels and 1-16Kbps D channel | | 1 |
| What's the default CDP holdtime in seconds for Cisco routers?
A.) 30 seconds
B.) 180 seconds
C.) 90 seconds
D.) 60 seconds | | 3 |
| Which of the following are valid WAN terms?
A.) DTE
B.) DCE
C.) Demarc
D.) CPE | | 2 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
