| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify 3 characteristics of ISDN?
A.) Transports voice and data
B.) Transports voice only
C.) Support both BRI and PRI
D.) Runs over existing phone lines
E.) Same as X.25 | | 1 |
| Identify the command that configures the bandwidth to 56K?
A.) Router(config-if)# bandwidth 56000
B.) Router(config-if)# bandwidth 56k
C.) Router(config)# bandwidth 56
D.) Router(config-if)# bandwidth 56 | | 1 |
| In Novell's use of RIP, there are two metrics used to make
routing decisions. Select the two metrics.
A. Ticks.
B. Hops
C. Loops
D. Counts | | 2 |
| What does a Standard IP Access-list use as test criteria?
A.) IP source address
B.) IP source and destination address, protocol numbers and
port numbers
C.) IPX source and destination address
D.) Source MAC address | | 1 |
| Which service takes information from multiple sources and
allocates bandwidth on a single media?
A. Time-division Multiplexing (TDM)
B. Signaling System 7 (SS7)
C. X.25
D. Frame relay | | 1 |
| Which can be logged by IPX extended access lists?
A.) source address
B.) protocol
C.) source socket
D.) access list number
E.) destination socket
F.) destination address | | 1 |
| hi... i am usin packet tracer 5.0.. i hav connect two
routers A and B. A has 200.100.25.100 and 1.0.0.1 and router
B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1
and 1.0.0.2... now i want to route 200.100.25.100 and
200.10.50.100 usin rip.. i enable rip in both the routers...
but whn i give the command show ip route... i jus get this
Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA
- OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF
NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF
external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 -
IS-IS level-2, ia - IS-IS inter area * - candidate default,
U - per-user static route, o - ODR P - periodic downloaded
static route Gateway of last resort is not set A# so can
sombody tell me where i hav gone wrong...
thanku | | 4 |
| What is the standard ISDN term for a non-native analog
telephone?
A.) TE1
B.) TA
C.) LE
D.) TE2
E.) ET | | 1 |
| the term which used for describe physical alyout of network
mine answer-topology | | 1 |
| Explain usage of ICMP in IP routing | | 2 |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecting to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecting to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 2 |
| Which addresses are valid host addresses?
A. 201.222.5.17
B. 201.222.5.18
C. 201.222.5.16
D. 201.222.5.19
E. 201.222.5.31 | | 2 |
| What are the OSPF router rules???? | NIIT | 6 |
| Given the following descriptions of layers of the OSI model
1) This layer segments and reassembles data into a data stream
2) This layer manages device addressing tracks the location
of devices on the network and determines the best way to
move data
3) This layer provides the physical transmission of the
data and handles error notification network topology and
flow control.
Choose the statement that lists the layers in the order
described above
A. physical data link network
B. physical session data link
C. data link network transport
D. data link transport network
E. transport network data link
F. transport data link network | | 1 |
| What's the default CDP holdtime in seconds for Cisco routers?
A.) 30 seconds
B.) 180 seconds
C.) 90 seconds
D.) 60 seconds | | 2 |
| The Datalink Layer is broken down into 2 layers, LLC and
MAC. The LLC
establishes media independence and what else?
A.) Provides Windowing.
B.) Provides flow control.
C.) Provides SAP's (Service Access Points).
D.) The Datalink layer does not have sublayers.
E.) Provides SAP's (Service Advertising Protocol).
F.) RIP Updates. | | 1 |
| Where is the point between the customers site and the phone
carrier that responsibility changes?
A.) CO
B.) Demarc
C.) DCE
D.) DTE
E.) CPE | | 1 |
| Which two steps are required to confound and apply standard
access lists on an interface? (Choose two)
A. define an access list number and its parameters
B. enable an interface to become part of the access list group
C. define the number of access lists to be supported on an
interface
D. copy the access list definition to each interface that
will support it | | 2 |
| How we ping ICMP a NIC with a correct IP address but with
wrong MAC address
Do all NIC's can run inpromiscuous mode | Cisco | 3 |
| Which router command allows you to view the entire contents
of all access lists?
A. Router# show interface
B. Router> show ip interface
C. Router# show access-list
D. Router> show all access-list | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
