Identify 2 features of PPP CHAP authentication? A.) Username and passwor

Advertise your Business Here

Refer this Site

Login | Sign Up


	Do you have a collection of Interview Questions and interested to share with us!! Please send that collection to along with your userid / name. ThanQ

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Identify 2 features of PPP CHAP authentication?

A.) Username and password is sent in clear text

B.) Authentication messages are sent periodically during the
connection

C.) Less secure then PAP

D.) Local router 'challenges' the remote router

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Identify 2 features of PPP CHAP authentication? A.) Username and password is sent in clear text B.) Authentication messages are sent periodically during the connection C.) Less secure then PAP D.) Local router 'challenges' the remote router

Answer
# 1

Answer: B D

PPP CHAP authentication message are sent periodically during the

connection by challenging the other end of the connection.

It is more secure than PAP and passwords and username are
encrypted.

Is This Answer Correct ?

0 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


What is the IP extended access list range? A.) 1000-1099 B.) 100-199 C.) 1-99 D.) 101-200		3
what is the default ad value of the interface directly coneted to router. as for exmaple ad value of ospf is 90 then from ehternet the network is conected whta is difault value of that directly conected interface. what is the defalt ad value of bgp whta is access llist and how many type of access list what is vlan what is vpn how e congigure the router what is mpls these are the question skrd to me at tcs i have replyed all ecxept the first one	TCS	1
Which line from a show spantree 1 command output indicates that virtual LAN 1 (VLAN1) is functioning properly? A. Root pod is FastEthernet 0/26 B. Port Ethernet 0/1 of VLAN1 is Forwarding C. Designated port is Ethernet 0/1, path cost 10 D. Designated root has priority 0 address 00D0 588F B600 E. VLAN1 is executing the IEEE compatible Spanning Tree Protocol		1
Identify the command to configure the router to boot from an alternate IOS located in flash? A.) boot system flash IOS.exe B.) boot system tftp IOS.exe 172.16.5.1 C.) boot system alternate IOS.exe D.) boot system rom IOS.exe		1
How does a switch use store and forward? A.) By using a Class I repeater in a collision domain B.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface C.) By using broadcast addresses as source addresses D.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets		1
Which command, that is used to test address configuration, uses Time-To-Live (TTL) values to generate messages from each router. A. trace B. ping C. telnet D. bootp		1
Which can be true regarding VLANs? A.) They are created by location B.) They are created by function C.) They are created by department D.) They are created by group		1
Identify the default values that make up IGRP's composite metric? A.) Bandwidth B.) Load C.) Reliability D.) MTU E.) Delay		1
Which command will display the IPX routing table? A.) show routes B.) show routes ipx C.) show routes protocol=ipx D.) show ipx E.) show ipx route		1
In order to configure a Frame Relay subinterface with IP identify the 2 commands that must be configured on the physcial interface? A.) Router(config-if)# encapsulation frame-relay B.) Router(config-if)# no ip address C.) Router(config-if)#encapsulation subinterface frame-relay D.) Router(config)# subinterface s0 encapsulation frame-relay		2
Identify the named IP access-list number range? A.) 600 - 699 B.) 1 - 99 C.) 900 - 999 D.) 200 - 299 E.) none of the above		2
Which three basic switch functions increase available bandwidth on the networks? (Choose three) A. loop avoidance B. address learning C. hop count limiting D. broadcast filtering E. packet forward/filtering		3
Which command enables directly connected network 199.55.72.0 to be used by RIP? A. Router(config router)# rip 199.55.0.0 B. Router(config router)# rip 199.55.72.0 C. Router(config router)# network 199.55.0.0 D. Router(config router)# network 199.55.72.0		1
Which two of the following are valid ways to have multiple encapsulation types on a single interface? A.) This is not possible B.) subinterfaces C.) additional physical interfaces D.) secondary addresses		1
The following commands were entered at the command prompt of a Cisco router. What do they accomplish? access-list 1000 deny 9e.1234.5678.1212 4 access-list 1000 permit -1 interface ethernet 0 ipx network 9e interface ethernet 1 ipx network 4a interface serial 0 ipx network 1 ipx output-sap-filter 1000 A. File server advertisements from server 9e.1234.5678.1212 will not be forwarded on interface S0. B. All other SAP services, other than file server, from any source will be forwarded on S0. C. All other SAP services, other than print server, from any source will be forwarded on S0. D. Print server advertisements from server 9e.1234.5678.1212 will not be forwarded on interface S0.		1
What is the result of segmenting a network with a router into segments 1 and 2? A. It increases the number of collisions B. It decreases the number of broadcast domains C. It connects segment 1 and broadcasts to segment 2 D. It connects segment 1 and broadcasts from genre to segment 2		1
What does the term Base refer to in 100BaseT A. cabling type B. singnal type C. 100 mode type D. spectrum used E. speed category		2
What is an advantage of LAN segmentation? A.) Increases broadcasts. B.) Increases collisions. C.) Provides more protocol support. D.) Decreases broadcasts. E.) Routing protocol support.	Wipro	2
Identify the switching method that examines the destination MAC address as the frame is being received then begins forwarding the frame prior to receiving the entire frame? A.) Fragment-free B.) Store and Forward C.) Cut-through D.) Fast forward		1
Which command displays access list 111? A. show access-list 111 B. show ip access-list 111 C. display ip access-list 111 D. display access-list 111 details	Satyam	6

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com