| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What does the acronym ARP stand for?
A.) Address Resolution Phase
B.) ARP Resolution Protocol
C.) Address Resolution Protocol
D.) Address Recall Protocol | | 1 |
| The Cisco Discovery Protocol (CDP) periodically sends out a
multicast packet (at layer 2). Which command will alter the
default
interval of 60 seconds?
A.) cdp hold 111
B.) cdp wait 111
C.) cdp interval 111
D.) cdp 111
E.) cdp timer 111 | | 1 |
| You want a message to be displayed every time someone tries
to log
on to the router. Which command is required to accomplish
this task?
A.) motd#(message)#
B.) banner motd(message)
C.) banner motd#(message)#
D.) banner motd*(message)
E.) banner login#(message)# | | 1 |
| What is true about Link-State protocols?
A.) They maintain a more complex table than distant vector
protocols
B.) They maintain a less complex table than distant vector
protocols
C.) They use routing ports
D.) The maintain backup copies of the IOS | | 1 |
| In stp which protocol is used for detrming root port root
bridge ,forwarding port and blocking port | IBM | 1 |
| what is standard and extended acess list?
what are the commands for extended and acess list? | HCL | 3 |
| Hi Anyone can share the latest ICND1 (640-822)dumps updated
at 30 september 2009. specialy to Jatendra if you have any
updated about the ICND1 exam.will be remain thankful. | | 2 |
| How can you add the 192.168.100.0/30 network to EIGRP without
involving the
192.168.100.4/30 network as well? | | 3 |
| Which layer is responsible for coordinating communication
between
systems?
A.) Application
B.) Network
C.) Session
D.) Transport
E.) Physical
F.) Data Link | HCL | 2 |
| Which addresses are INCORRECTLY paired with their class?
A. 128 to 191, Class B
B. 192 to 223 Class B
C. 128 to 191, Class C
D. 192 to 223, Class C | | 2 |
| Which three of the following are true statements about
connection-oriented sessions?
A.) The segments delivered are acknowledged back to the
sender upon
their reception
B.) Any segments not acknowledged the are retransmitted by
the receiver
C.) A manageable data flow is maintained in order to avoid
congestion,
overloading and loss of any data
D.) Segments are sequenced back into their proper order upon
arrival at
their destination | | 1 |
| What does the "IPX maximum-paths 2" command accomplish?
A. It enables load sharing on 2 paths if the paths are equal
metric paths.
B. It sets up routing to go to network 2.
C. It is the default for Cisco IPX load sharing.
D. It enables load sharing on 2 paths if the paths are
unequal metric paths. | | 2 |
| What is the default encapsulation and frame type on an Ethernet
interface when enabling Novell?
A.) SNAP
B.) Ethernet_II
C.) 802.2
D.) 802.3
E.) SAP
F.) Token_SNAP | | 1 |
| What is the administrative distance for IGRP?
A.) 90
B.) 120
C.) 110
D.) 100 | | 2 |
| What is a characteristic of Store and Forward switches?
A.) They work at wire speed.
B.) They are the same as Cut-Through switching in 'prune' mode.
C.) They forward based on transport layer info.
D.) They forward the frame before it is completely read.
E.) They increase latency. | | 1 |
| Which is not a common problem with Distance-Vector routing?
A.) Slow convergence.
B.) Complex configuration.
C.) Routing loops.
D.) Periodic updates can slow convergence.
E.) Counting to infinity. | | 1 |
| In which two modes can the ICMP ping command be used?
(Choose two)
A. user
B. privileged
C. global configuration
D. interface configuration | | 1 |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| Identify the hardware component that stores the backup
configuration?
A.) RAM
B.) NVRAM
C.) Flash
D.) ROM | | 1 |
| What field tells the Internet layer how to handle an IP packet?
A. Type of Service
B. Identification
C. Flags
D. Frag Offset | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
