| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which type of switching is considered to be 'wire speed?'
A.) Cut-Through
B.) Multiplexed
C.) Inverted
D.) Layer 4
E.) Store and Forward
F.) Layer 3 | | 1 |
| Which command will display the IPX routing table?
A.) show routes
B.) show routes ipx
C.) show routes protocol=ipx
D.) show ipx
E.) show ipx route | | 1 |
| What is the connection oriented protocol in the TCP/IP
protocol stack?
A. IP
B. UDP
C. TCP
D. DNS
E. OSPF | HCL | 5 |
| What is the Function of Router? | | 4 |
| Which of the following are characteristics of UDP?
A.) UDP is connection oriented.
B.) UDP is used with TFTP.
C.) UDP is unreliable.
D.) UDP is connectionless.
E.) UDP is at the transport layer.
F.) UDP uses no acknowledgements. | | 1 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| Identify the command mode necessary to enter the extended ping
command?
A.) Router#
B.) Router>
C.) Router(config)#
D.) Router(ext-ping)# | | 3 |
| 'Show cdp neighbors detail' show the following 3 pieces of
information?
A.) Hardware platform
B.) Software version
C.) Same as 'show version' command
D.) Up to 1 address for each protocol
E.) Non-direct connected routers | | 2 |
| If you are running Token Ring with Novell IPX routing, which
encapsulation
should you use?
A.) SAP
B.) SNAP
C.) 802.5
D.) 802.2 | | 1 |
| Which IP address and wildcard mask would you use in your
ACL to block all the
hosts in the subnet 192.168.16.43/28? | Siemens | 2 |
| What does 'P' mean when running a Trace?
A.) Good route
B.) Protocol unreachable
C.) Source Quench
D.) Destination unreachable | | 2 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| Identify the purpose of the TCP 3 step handshake?
A.) Setup a un-reliable connection
B.) Initialize routing tables
C.) Synchronize sequence numbers between hosts
D.) Connection tear down process | | 1 |
| Identify the command mode necessary to enter the extended ping
command?
A.) Router#
B.) Router>
C.) Router(config)#
D.) Router(ext-ping)# | | 1 |
| You are logged into a router, what command would
show you the IP addresses of routers connected to you?
A. show cdp neighbors detail
B. show run
C. show neighbors
D. show cdp | | 2 |
| You are a system administrator on a NetWare network, you are
running NetWare 4.11 and you cannot communicate with your
router. What is the likely problem?
A. NetWare 4.11 defaults to 802.2 encapsulation.
B. NetWare 4.11 defaults to 802.3 encapsulation
C. Cisco routers only work with NetWare 3.11.
D. NetWare 3.11 defaults to 802.2 encapsulation. | | 1 |
| Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe | | 1 |
| Which ISDN specification deals with call Setup and Teardown?
A.) Q-Series
B.) J-Series
C.) I- Series
D.) C- Series
E.) F-Series | | 1 |
| If i connect two routers through ethernet cable and serial
cable then which has high speed and which is better among
two? | Compaq | 9 |
| Which ISDN specification series deals with Concepts and
Terminology?
A.) C- Series
B.) I- Series
C.) Q-Series
D.) 911-Series
E.) J-Series
F.) F-Series | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
