| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Of the following characteristics, which apply to UDP?
Connection-oriented
Connectionless
Error checking
Low overhead
Best-effort delivery
| | 3 |
| What is the last step in data encapsulation?
A.) User information is converted into data.
B.) Segments are converted into datagrams and packets.
C.) Frames are put into bits.
D.) Data is converted into segments.
E.) Packets are put into logical frame. | | 1 |
| Which statement about switched and routed data flows is correct?
A. Switches create a single collision domain and a single
broadcast domain. Routers provide separate collision domains
B. Switches create separate collision domains but a single
broadcast domain. Routers provide a separate broadcast domain
C. Switches create a single collision domain and separate
broadcast domains. Routers provide a separate broadcast
domain as well
D. Switches create separate collision domains and separate
broadcast domains. Routers provide separate collision domains | | 1 |
| what is burst rate | ASD-Lab | 1 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| Cisco's implementation of ISDN BRI has multi protocol support,
SNMP MIB support, and what other features?
A.) Call waiting
B.) Compression
C.) ADSL
D.) 1.544 Mbps
E.) Call screening
F.) Negative 'G' support | | 1 |
| Access lists are numbered. Which of the following ranges
could be
used for an IP access list?
A. 600 - 699
B. 100 - 199
C. 1 - 99
D. 800 - 899
E. 1000 - 1099 | | 1 |
| Which of the following is an example of the Network Layer?
A.) LLC
B.) SQL
C.) Token Ring
D.) IPX
E.) SPX | | 1 |
| You are conferring a Frame Relay router with subinterfaces
on interface Serial 0 Which subinterfaces numbers could you
use for this configuration?
A. 1 and 2
B. 0 2 and 0 3
C. 1 0 and 1 1
D. 0 1 a and 0 1 | | 1 |
| Which command loads a new version of the Cisco IOS into a
router?
A. copy flash ftp
B. copy ftp flash
C. copy flash tftp
D. copy tftp flash | | 1 |
| Which layer is responsible for providing mechanisms for
multiplexing
upper-layer application, session establishment, and tear
down of virtual
circuits?
A.) Session
B.) Network
C.) Physical
D.) Transport
E.) Application
F.) Presentation | | 1 |
| What are the two most common request/reply pair with ICMP
messages when using the ping command? (Choose two)
A. echo reply
B. echo request
C. source quench
D. fragment onset
E. information redirect
F. destination reachable
G. echo control message | | 1 |
| Which command displays the IP addresses assigned to specific
host names?
A. show hosts
B. show interface
C. ping host name
D. config host name
E. show host mapping
F. show host ip address
G. trace ip addresses host name
H. a partridge in a pear tree | | 1 |
| Identify the command to display the hardware platform
information?
A.) show all
B.) show platform
C.) display hardware
D.) show version | | 1 |
| How many collisions are caused by transmitting and receiving
frames simultaneously in a full-duplex Ethernet technology?
A. one
B. two
C. none
D. several | | 1 |
| What is the bit length and expression form of a MAC address?
A. 24 bits expressed as a decimal number
B. 24 bits expressed as a hexadecimal number
C. 36 bits expressed as a binary number
D. 48 bits expressed as a decimal number
E. 48 bits expressed as a hexadecimal number | | 2 |
| Describe End to End network services: (Choose all that apply)
A.) Best Route selection
B.) Accomplished Segment by Segment, each segment is autonomous
C.) Flow Control & Data Integrity
D.) Best efforts packet delivery | | 1 |
| What does the parameter -- LOG -- do on an IPX access list?
A.) The log keyword is not a valid option.
B.) Read the LOG to figure out what traffic to deny.
C.) Logs the creation of the access list.
D.) Logs IPX access control list violations whenever a
packet matches a
particular access list entry.
E.) Ensures the IPX protocol places a log in the fireplace. | | 1 |
| Identify the purpose of the following command 'ip route
192.168.100.0
255.255.255.0 10.1.0.1'
A.) Enabling a dynamic routing protocol
B.) Creating a static route to the 10.1.0.0 network
C.) Teaches the router about the distant network
192.168.100.0 and how it
can be reached via 10.1.0.1
D.) Assigining the IP address 192.168.100.0 to an interface | | 1 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
