| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 3 characteristics of IPX RIP?
A.) Distance vector
B.) Does not support multiple paths
C.) 60 second updates
D.) Default encapsulation is SAP
E.) Uses ticks and hop count as a metric | | 1 |
| Identify the true statement regarding subnetting?
A.) Allows for more host address
B.) Borrow bits from the network portion of the address
C.) Allows for unlimited number of networks
D.) Borrow bits from the host portion of the address | | 1 |
| During encapsulation, in which order is information packaged?
A. Data, Packet, Segment, Frame
B. Segment, Data, Packet, Frame
C. Data, Segment, Packet, Frame
D. Packet, Data, Segment, Frame
E. Frame, Data, Segment, Packet
F. Bread, Peanut Butter, Jelly, Bread | | 2 |
| Hi-
Salmaan my name is Shadab Khan and nick Khangkp
ok salmaam plz tell me about of NAT plz | | 3 |
| Given the following descriptions of layers of the OSI model
1) This layer segments and reassembles data into a data stream
2) This layer manages device addressing tracks the location
of devices on the network and determines the best way to
move data
3) This layer provides the physical transmission of the
data and handles error notification network topology and
flow control.
Choose the statement that lists the layers in the order
described above
A. physical data link network
B. physical session data link
C. data link network transport
D. data link transport network
E. transport network data link
F. transport data link network | | 1 |
| IGRP supports a feature that allows traffic to be
distributed among up to 6 (4 default) paths to provide
greater overall throughput and reliability. What is this
called?
A. unequal-cost load balancing
B. equal-cost load balancing
C. proportionate load balancing
D. low cost load balancing | | 1 |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Router(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| All equipment located at the customers site is called:
A.) CPE
B.) CO
C.) DCE
D.) Demarc
E.) DTE | | 1 |
| Which two commands show your access lists? (Choose two)
A. show filters
B. show access-lists
C. show ip access-lists
D. show running-config | | 1 |
| Describe End to End network services: (Choose all that apply)
A.) Best Route selection
B.) Accomplished Segment by Segment, each segment is autonomous
C.) Flow Control & Data Integrity
D.) Best efforts packet delivery | | 1 |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| What is the purpose of ARP?
A.) IP to host name resolution
B.) Host name to IP address resolution
C.) Mac to IP address resolution
D.) IP to Mac address resolution | | 3 |
| How can an Ethernet switch improve network performance?
Choose three | | 1 |
| As a system administrator, you want to debug igrp but are
worried that the "debug IP igrp transaction" command will
flood the console. What is the command that you should
use?
A. debug IP igrp event
B. debug IP igrp-events
C. debug IP igrp summary
D. debug IP igrp events | | 1 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| IPX routing updates occur how often?
A.) Every 30 seconds
B.) Every 60 seconds
C.) Only as needed
D.) When the remote router asks for an update | | 1 |
| Hi, I have packet tracer 5.0. I want to test intervlan
routing routing. Can someone plz tell me about intervlan
routing? | | 1 |
| Which layer is responsible for synchronizing sending and
receiving
applications?
A.) Presentation
B.) Session
C.) Transport
D.) Application
E.) Network | | 2 |
| Which two steps are part of the process of creating Frame
Relay subinterfaces on a point to point connection? (Choose
two)
A. configure the router to forward all broadcast packets
B. remove any network address assigned to the physical interface
C. configure the local data link connection identifier
(DICI) for the subinterfaces
D. cartoon the total committed information rate (CIP)
available among the subinterfaces | | 1 |
| What is an advantage of LAN segmentation?
A.) Increases broadcasts.
B.) Increases collisions.
C.) Provides more protocol support.
D.) Decreases broadcasts.
E.) Routing protocol support. | Wipro | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
