| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which OSI layer establishes, maintains and terminates sessions
between
applications?
A.) Application
B.) Physical
C.) Data-Link
D.) Presentation
E.) Network
F.) Session | | 1 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| Repeaters work at which layer of the OSI model?
A.) Network
B.) Session
C.) Transport
D.) Physical | | 2 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| Which layer is responsible for routing through an internetwork?
A.) Physical
B.) Session
C.) Network
D.) Transport
E.) Application
F.) Data Link | | 2 |
| Which of the following are ways to provide login access to a
router?
A.) HTTP
B.) Console
C.) Telnet
D.) Aux Port
E.) SNMP
F.) LLC | | 1 |
| What command do you use to disable domain lookup?
A.) no domain-lookup
B.) domain no-lookup
C.) lookup no-domain
D.) no ip domain-lookup | | 1 |
| What is convergence time?
A.) The update time
B.) The time it takes to reload a router
C.) The time it takes for a packet to reach its destination
D.) The time is takes for all routers update their tables
after a change
takes place | | 1 |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 1 |
| Which statement is true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not a the same
time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| UDP works at which layer of the DOD model?
A.) Internet
B.) Host-to-Host
C.) Transport
D.) Data Link | | 1 |
| When you enter router passwords during the setup dialog what
is the difference between enable and the enable secret
passwords?
A. The enable password is encrypted
B. The enable secret password uses IPSec password authentication
C. The enable secret password cannot be seen as clear text
when viewing the configuration
D. The enable secret password acts as a backup in case the
enable password is compromised | Wipro | 6 |
| The CSMA/CD Ethernet IEEE committee is defines as which of the
following?
A.) 802.2
B.) 802.3
C.) 802.4
D.) 802.5 | | 1 |
| What is the result of segmenting a network with a router
into segments 1 and 2?
A. It increases the number of collisions
B. It decreases the number of broadcast domains
C. It connects segment 1 and broadcasts to segment 2
D. It connects segment 1 and broadcasts from genre to segment 2 | | 1 |
| What type of Ethernet operation allows only one entity to
transmit
at a time? For example, if someone else is transmitting,
they must wait.
A.) Full-Duplex
B.) Dual-Duplex
C.) Half-Duplex
D.) Latex
E.) Quarter-Duplex
F.) Suplex | | 1 |
| Which of the following is true regarding standard ISDN BRI
service?
A.) ISDN BRI B channels are typically 64K.
B.) ISDN BRI can handle only voice.
C.) ISDN BRI can handle only data.
D.) ISDN BRI has 2B and 1D channels.
E.) ISDN BRI D channels are 16K.
F.) ISDN BRI can handle voice and data. | | 1 |
| CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment | | 1 |
| Identify the true statements about the following access list:
Access-list 101 deny tcp 192.10.172.0 0.0.0.255 any eq 23
Access-list 101 permit ip any any
A.) This access list prevents the host 192.10.172.0 from
telneting
B.) This access list prevents any telnet traffic from subnet
192.10.172.0/24
C.) This access list filters some telnet access
D.) This access list denies any telnet traffic to subnet
192.10.172.0/24
E.) This access list is invalid
F.) The netmask on the this access list is reversed | | 1 |
| Identify the switching method that receives the entire frame
then
dispatches it?
A.) Cut-through
B.) Receive and forward
C.) Store and forward
D.) Fast forward | | 1 |
| Which two statements about IP RIP are true? (Choose two)
A. It limits hop counts to 31
B. It is a link state routing protocol
C. It uses autonomous system numbers
D. It is capable of load sharing over multiple paths
E. It uses bandwidth as the metric for path selection
F. It broadcasts updates every 30 seconds by default | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
