| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the switching method that examines the destination MAC
address as the frame is being received then begins
forwarding the frame
prior to receiving the entire frame?
A.) Fragment-free
B.) Store and Forward
C.) Cut-through
D.) Fast forward | | 1 |
| What is the default switching method for the Cisco 5000 series?
A.) Cut-through
B.) Store-and-splice
C.) Latency
D.) Store-and-forward | | 1 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 3 |
| bWhich form of PPP error detection on Cisco routers monitors
data
dropped on a link?
A. Quality
B. Magic Number
C. Error Monitor
D. Droplink | | 1 |
| Where is the backup configuration file stored?
A.) RAM
B.) ROM
C.) Console
D.) NVRAM | | 1 |
| How many LMI types are available on Cisco routers?
A.) Four
B.) Two
C.) Five
D.) Three | | 1 |
| When using RIP, routing updates are broadcast every ____
seconds.
A. 30
B. 10
C. 60
D. 90 | | 1 |
| Identify 3 methods not used to prevent routing loops?
A.) Holddown timers
B.) Sequence numbers
C.) Triggered updates
D.) Split horizon
E.) Area hierarchies
F.) Order of router startup | | 1 |
| What type of switching creates variable latency through the
switch?
A.) Cut-Through
B.) Inverted
C.) Layer 4
D.) Multiplexed
E.) Store and Forward | | 1 |
| Based upon the 1st octet rule identify the range for a Class A
address?
A.) 1 - 126
B.) 192 - 223
C.) 128 - 191
D.) 1 - 191 | | 4 |
| Which layer is responsible for determining if sufficient
resources
for the
intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 2 |
| Identify the command that configures serial0 for PPP
encapsulation?
A.) Router(config)# encapsulation ppp
B.) Router(config-if)# encapsulation serial ppp
C.) Router(config-if)# encapsulation ppp
D.) Router# encapsulation ppp | | 1 |
| Hi Jitendera, I continuously read your answers which is
more knowlegable than books...
Q.I am facing some problems in subnetting.can you plzz
explain the subnetting process.. will be remain thankful | | 3 |
| Which OSI layer provides mechanical, electrical & procedural
specifications for activating, maintaining physical link?
A.) Presentation
B.) Network
C.) Application
D.) Physical
E.) Transport
F.) Data-Link | | 1 |
| Hi,
I am littl bit confused about ip Addressing scheme? can
someone tell me how can we assign ip addresses to pc | | 2 |
| As a system administrator, you want to debug igrp but are
worried that the "debug IP igrp transaction" command will
flood the console. What is the command that you should
use?
A. debug IP igrp event
B. debug IP igrp-events
C. debug IP igrp summary
D. debug IP igrp events | | 1 |
| What's the default CDP holdtime in seconds for Cisco routers?
A.) 30 seconds
B.) 180 seconds
C.) 90 seconds
D.) 60 seconds | | 2 |
| In version 11.2 of the IOS, a Cisco router configured for
frame-relay can automatically detect the LMI type. What is
this known as?
A.) Psychic
B.) ESP
C.) Inverse ARP
D.) Hello
E.) Reverse ARP
F.) Autosense | | 1 |
| When you cords an IP address on a place router which command
stale the IP processing on the interface?
A. ip enable
B. network ip-address
C. ip address ip-address subnet mask
D. the exit command from the enabled configuration
E. copy running-configuration to startup-configuration | | 3 |
| What is the routing metric used by IGRP?
A.) MTU, delay, bandwidth, reliability, and loading
B.) Count to infinity
C.) TTL
D.) Hop count | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
