| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| Which command displays the IPX SAP table?
A.) show ipx sap
B.) show sap
C.) show ipx interface
D.) show ipx servers
E.) show ipx | | 1 |
| Identify the purpose of the following command 'ip route
192.168.100.0
255.255.255.0 10.1.0.1'
A.) Enabling a dynamic routing protocol
B.) Creating a static route to the 10.1.0.0 network
C.) Teaches the router about the distant network
192.168.100.0 and how it
can be reached via 10.1.0.1
D.) Assigining the IP address 192.168.100.0 to an interface | | 1 |
| What does a router do with a packet that it does not have a
destination
network for?
A.) Sends it to the Serial port
B.) Drops the packet
C.) Sends it back out the same interface it received it in
D.) Forwards the packet to the next hop | | 1 |
| Identify the command to configure ALL the default VTY ports?
A.) Router(config)# line vty 0 4
B.) Router# line vty 0 4
C.) Router(config)# line vty
D.) Router(config)# line vty 0 | Accel | 2 |
| Identify the purpose of ARP?
A.) Avoiding routing loops
B.) Determining a workstation's IP address
C.) Sending a directed broadcast
D.) Determining a workstation's MAC address | | 3 |
| Which range of possible numbers do standard ipx access lists
have?
A. 100 199
B. 600 699
C. 800 899
D. 1000-1099 | | 1 |
| What is a characteristic of Store and Forward switches?
A.) They work at wire speed.
B.) They are the same as Cut-Through switching in 'prune' mode.
C.) They forward based on transport layer info.
D.) They forward the frame before it is completely read.
E.) They increase latency. | | 1 |
| 7. What is an advantage to using switches in your network?
A. Addressing of hosts by DHCP
B. Ease of administration
C. Stops broadcast storms
D. Works like a repeater
| iGate | 2 |
| Which of the following are Distant Vector protocols?
A.) IGRP
B.) RIP
C.) OSFP
D.) EIGRP | | 1 |
| When you mistakenly type the wrong command
at the Router# prompt the router does a
DNS lookup which takes about 20 seconds.
Which command can you enter to prevent the
router doing this in future?
| | 2 |
| What key do you use to view the last command?
A.) Left Arrow
B.) Space Bar
C.) Up Arrow
D.) Right Arrow | | 2 |
| Identify the purpose of the Ping command?
A.) Share routing information with a neighbor router
B.) Transmit user data when buffers are full
C.) Test connectivity at layer 3
D.) Test entire protocol stack | | 2 |
| in the ospf area network dr and bdr selection procedure occur
let there are 4 router in that n/w r1 have the higher priority
then r2 and r2 have higher priority then r3 and so on
like that
r1>r2>r3>r4
now as we know that selection of dr and bdr based upon the
router priority so in this case r1 will be dr and r2 will be
bdr
now my question is that if i am going to implement 5th
router which have greater priority then r1 then will it become dr atomically
remember that i am not going change my 5 or 1st router property
answer that one please | | 2 |
| Which three tasks are required to confound a dial on demand
routing (DDR) Basic Rate Interface (BRI) connection?
(Choose three)
A. define static routes
B. confound the abler information
C. specify the interesting franc that can enable the link
D. define a DDR password to exchange when the link comes up | | 1 |
| What is an advantage of LAN segmentation?
A.) Increases broadcasts.
B.) Increases collisions.
C.) Provides more protocol support.
D.) Decreases broadcasts.
E.) Routing protocol support. | Wipro | 2 |
| what is the diffrence betwwen telnet and ssh.this question
is asked by nikhil and i am plasing the answer here insteed
of his personal mail.
| | 4 |
| 2. What are the valid ways to segment a LAN? (Choose all
that apply)
A. Repeater
B. Bridge
C. Switch
D. Router
| | 2 |
| Identify the 2 rules used when configuring a Distance Vector
routing protocol?
A.) Physically connected network(s)
B.) Configure the classful address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Configure all networks in Area0 | | 1 |
| Put the following steps of encapsulation into the correct order:
1) The data is broken into segments to be organized
2) Frames are converted to 1s and 0s to be put on the wire
3) Packets are converted into frames
4) Information that users enter is converted into data
5) The segments are changed to packets to be routed
A.) 4, 1, 3, 2, 5
B.) 4, 5, 1, 3, 2
C.) 2, 3, 1, 4, 5
D.) 4, 1, 5, 3, 2 | | 2 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
