Identify the definition of demarcation? A.) Date in which the WAN servic

Advertise your Business Here

Refer this Site

Login | Sign Up


	Ask Questions on ANYTHING, that arise in your Daily Life at FORUM9.COM

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Identify the definition of demarcation?

A.) Date in which the WAN service contract expires

B.) Cabling which extends from the WAN service provider to
the customer

C.) Division of responsibility, where the CPE ends and the
local loop

begins

D.) Equipment which is located at the customer premises

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Identify the definition of demarcation? A.) Date in which the WAN service contract expires B.) Cabling which extends from the WAN service provider to the customer C.) Division of responsibility, where the CPE ends and the local loop begins D.) Equipment which is located at the customer premises

Answer
# 1

Answer: C

Demarcation is the point in which responsibility changes hands.

Is This Answer Correct ?

0 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


Which two statements about a bridge are true? (Choose two) A. A bridge floods multicasts B. A bridge floods broadcasts C. A bridge does not flood multicasts D. A bridge does not flood broadcasts		1
What is proxy-ARP and how it is used and configured		1
The network portion of an address typically represents a: A.) Router B.) Ethernet MAC address. C.) Computer D.) Host E.) Segment		1
7. What is an advantage to using switches in your network? A. Addressing of hosts by DHCP B. Ease of administration C. Stops broadcast storms D. Works like a repeater	iGate	2
Which command specifies a second subinterface on serial interface 0? A. interface s 0.2 point-to-point B. interface 2 s.0 point-to-point C. suberinterface 2.s 0 point-to-point D. interface s 0 sub 2 point-to-point E. interface s 0.1 point-to-point sub 2		1
How do you disable CDP on the entire Router? A.) Router#no cdp run B.) Router(config-if)# no cdp enable C.) Router(config)# no cdp enable D.) Router(config)# no cdp run		1
Identify the command to disable CDP on an interface? A.) Router(config-if)# no cdp enable B.) Router(config-if)# no cdp run C.) Router# no cdp enable D.) Router(config-if)# no cdp		1
Your network uses a Class C address of 210.10.10.0. You must now split up the network into separate shores to handle multiple buildings separated by routers. Which two steps must you take to determine the proper shored mask for your networks? (Choose two) A. determine the number of seperate networks required B. determine how many devices will require DHCP addressing C. determine the maximum number of hosts that will be on each shored D. determine the miniumum number of hosts that will be on each shored E. determine which router will be the IP default gateway for each shored		1
Which of the following are logged when IP access list logging is enabled? A.) source address B.) protocol C.) source port D.) destination address E.) access list number F.) destination port		1
what is hop count?		11
Company XYZ has an employee that works out of the home. The employee runs big client server applications and must quickly transfer large files. The company wants the best cost/benefit on this connection. What would be the most practical solution? A. an ISDN Basic Rate Interface (BRI) connection to the user at home B. a dedicated T1 connection to the user at home C. a dedicated Frame Relay connection to the user at home. D. a standard 28.8 analog dialup connection to the user at home.		1
Which statement is true regarding the user exec and privileged exec mode? A.) The '?' only works in Privileged exec B.) Privileged exec is a subset of the user exec mode C.) They both require the enable password D.) User exec is a subset of the privileged exec mode		1
Identify the command to configure the router to boot from an alternate IOS located in flash? A.) boot system flash IOS.exe B.) boot system tftp IOS.exe 172.16.5.1 C.) boot system alternate IOS.exe D.) boot system rom IOS.exe		1
What does the Frame Relay switch use to distinguish between each PVC connection? A. data-link connection identifiers (DLCIs) B. BECNs C. FECNs D. the Local Management Interface (LMI)		2
CSMA/CD stand for which of the following? A.) Carrier Sense, Multiple Access with Collision Detection B.) Collision Sense, Multiple Access with Collision Detection C.) Collision Sense, Multiple Access with Carrier Detection D.) Carrier Sense, MAC address with Collision Detection		3
Which statement about the Committed Information Rate (CIP) is true? A. It is the rate in bits per second at which the Frame Relay switch agrees to transfer data B. It is the clock speed (pod speed) of the connection (local loop) to the Frame Relay cloud C. It is the maximum number of bits that switch can transferduring any Committed Rate Measurement Interval D. It is a signaling standard between the 3PE device and FP switch. It is responsible for managing the connection and maintaining status between the devices.		1
How many subnets can be gained by subnetting 172.17.32.0/23 into a /27 mask, and how many usable host addresses will there be per subnet?		7
Identify the 2 commands that will display the status and information about interface E0 only? A.) show interface ethernet E0 B.) show interface E0 C.) show E0 D.) show int E0 E.) show interface		1
what is stp.	IBM	3
Which OSI Reference Layer is concerned with path determination? A.) Datalink B.) Physical C.) Network D.) Transport E.) Session		2

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com