| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which service takes information from multiple sources and
allocates bandwidth on a single media?
A. Time-division Multiplexing (TDM)
B. Signaling System 7 (SS7)
C. X.25
D. Frame relay | | 1 |
| In which three situations is a hold down timer reset?
(Choose three)
A. when the hold down timer expires
B. when infinity is finally defined as some maximum number
C. when the router exchanges update summaries at area borders
D. when the router detects faulty LSPs propagating through
the internetwork
E. when another update is received indicating a new route
with a better metric
F. when another update is received indicaing the original
route to the network has been restored
G. when the router receives a processing task proportional
to the number of links in the internetwork | | 1 |
| Which OSI layer incorporates the MAC address and the LLC?
A.) Data link
B.) Network
C.) Physcial
D.) Transport | | 1 |
| What is the total bandwidth of all channels on a BRI circuit?
A. 56 kps
B. 64 kps
C. 112 kps
D. 128 kps
E. 144. kps | | 5 |
| You create the following standard access-list
access-list 1 deny 1.1.1.1
access-list 1 deny 2.2.2.2
int e0
ip access-group 1 in
Which of the following statements are true, with regard to
traffic flowing
into E0?
A.) This will stop IP packets with a source address of
1.1.1.1 only.
B.) This will stop all IP packets.
C.) This is an invalid configuration.
D.) This will stop no IP packets.
E.) This will stop IP packets with a source address of
2.2.2.2 only.
F.) This will stop IP packets with a source address of
1.1.1.1 and 2.2.2.2. | | 1 |
| 255.255.255.128/what is the n/w id ,broadcast id and the
number of valid host(according to disco rules) | Reliance | 2 |
| Identify 3 characteristics of an IP address?
A.) Contains a network portion and a host portion
B.) 32 bits long
C.) Unique to each network
D.) Part of the default Cisco configuration
E.) Referred to as the hardware address | Infosys | 3 |
| Identify the IPX standard access-list number range?
A.) 600 - 699
B.) 1000 - 1099
C.) 1 - 99
D.) 100 - 199
E.) 800 - 899 | | 1 |
| Which command will show you if you have a DTE or DCE
cable connected to an interface? | | 3 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not a
the same time | | 2 |
| What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923 | | 3 |
| What does the following series of commands accomplish?
router igrp 71
network 10.0.0.0
router igrp 109
network 172.68.7.0
A. It isolates networks 10.0.0.0 and 172.68.7.0.
B. It loads igrp for networks 109 and 71.
C. It disables RIP.
D. It disables all routing protocols. | | 1 |
| When a router knows the IP address, but does not know the MAC
address of
the device it wishes to contact, it uses the ARP (Address
resolution
protocol) to determine the MAC address. After it learns the
MAC address,
it stores this information in the ARP cache. What is the
command to view
the ARP cache?
A.) sh mac
B.) show cache
C.) show arp
D.) sh arp interfaces
E.) show ip cache | | 2 |
| The following is partial output from a routing table ;
'192.168.10.0 [100/1300] via 10.1.0.1, 00:00:23, Ethernet1'
Which routing protocol is being used? (assuming defaults
have not been
changed)
A.) OSPF
B.) RIP
C.) BGP
D.) IGRP | | 1 |
| Which two types of route table entries are used by a Layer 3
router to determine the appropriate path to destination?
(Choose two)
A. static route entry
B. default route entry
C. Dynamic route entry
D. temporary route entry
E. permanent route entry | | 1 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not at
the same time | | 1 |
| Which of the following are valid WAN terms?
A.) DTE
B.) DCE
C.) Demarc
D.) CPE | | 1 |
| Which term describes the process in which frames from one
network system are placed inside the frames of another
network system?
A. bridging
B. tunnelling
C. data link control
D. generic routing
E. packet switching | | 1 |
| 10. Which STP state populates the MAC address table but
doesn't forward data frames?
A. Blocking
B. Listening
C. Learning
D. Forwarding
| Cisco | 3 |
| How do you find the parameters that you can use with the SHOW
command?
A.) ? show
B.) show ?
C.) debug show
D.) help
E.) sh? | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
