| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Hi,
I am littl bit confused about ip Addressing scheme? can
someone tell me how can we assign ip addresses to pc | | 2 |
| How do you get help on a command after you have received the
% incomplete command response from a switch CLI?
A. type "history" to review the prompt before the error
B. enter a question mark to display all the console commands
C. type help followed by the command to see command parameters
D. reenter the command followed by a question mark to view
keywords | | 1 |
| What do the following commands accomplish?
access-list 1 permit 172.16.0.0 0.0.255.255
interface ethernet 0
IP access-group 1 out
interface ethernet 1
IP access-group 1 out
A. Only traffic from the source network 172.16.0.0 will be
blocked.
B. Only traffic from the source network 172.16.0.0 will be
forwarded.
Non-172.16.0.0 network traffic is blocked.
C. Non-172.16.0.0 traffic will be forwarded.
D. All traffic will be forwarded. | | 1 |
| Identify the command to display the status of the Frame Relay
virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual | | 1 |
| Sequence and acknowledgement numbers are used for?
A.) Layer transitioning
B.) Flow control
C.) Port number addressing
D.) Reliability | | 1 |
| When using access lists, what does a Cisco router check first?
A. To see if the packet is routable or bridgeable
B. The destination address
C. The source address
D. The packet contents | | 1 |
| What is the default LMI type for Cisco Routers that are using
Frame-Relay?
A.) Annex D
B.) Q933A
C.) Cisco
D.) IETF
E.) ARPA
F.) Anex A | | 2 |
| What does the command show access-lists 101 list?
A. all defended access lists
B. all access lists within the router
C. the contents of standard access list 101
D. the contents of defended access list 101 | | 1 |
| What protocols can you use while testing Trace?
A.) DECnet
B.) CLNS
C.) IP
D.) Old Vines
E.) Vines
F.) Chaos | | 1 |
| Which of the following would be displayed by the command
'SHOW CDP
NEIGHBOR DETAIL'?
A.) The incoming/outgoing port.
B.) The hardware platform.
C.) One address per protocol.
D.) Amount of Flash Memory Available
E.) The routers hostname.
F.) The subnet mask, if IP is configured. | | 1 |
| What field tells the Internet layer how to handle an IP packet?
A. Type of Service
B. Identification
C. Flags
D. Frag Offset | | 1 |
| what is difference between
1 pap and chap(quite easy but need on line answer)
2 chap and ms-chap(plz describe briefly)
now i have posted the question is there any one to help me?
| | 1 |
| what are two security appliances that can be installed a
network | | 7 |
| What does the "IPX maximum-paths 2" command accomplish?
A. It enables load sharing on 2 paths if the paths are equal
metric paths.
B. It sets up routing to go to network 2.
C. It is the default for Cisco IPX load sharing.
D. It enables load sharing on 2 paths if the paths are
unequal metric paths. | | 2 |
| "arpa" is used by the Cisco IOS for which encapsulation
types?
A. Ethernet_II
B. Ethernet_802.3
C. Ethernet_802.2
D. Ethernet_SNAP | | 1 |
| Identify the 4 that are not LAN technologies?
A.) HDLC
B.) FDDI
C.) 802.5
D.) HSSI
E.) SDLC
F.) Frame Relay | AXA | 1 |
| What parameter is used with statically assigned routers to tell
packets which interface to use to reach a distant network?
A.) Mask
B.) Subnet
C.) Default gateway
D.) Interface | | 1 |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| Which of the following protocols are used for logical network
addressing?
A.) IP
B.) TCP
C.) ARP
D.) ICMP
E.) RARP
F.) BootP | | 1 |
| Identify the following command to configure a secret password to
'cisco'?
A.) Router(config)#enable password cisco secret
B.) Router(config)#enable secret cisco
C.) Router(config)#enable secret password cisco
D.) Router(config)#set secret = cisco | | 1 |
| |
| For more CCNA Interview Questions Click Here |