| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| You are given the following address: 128.16.32.13/30.
Determine the subnet mask, address class, subnet address,
and broadcast address.
A. 255.255.255.252, B,128.16.32.12, 128.16.32.15
B. 255.255.255.252, C,128.16.32.12, 128.16.32.15
C. 255.255.255.252, B,128.16.32.15, 128.16.32.12
D. 255.255.255.248, B,128.16.32.12, 128.16.32.15 | | 1 |
| what is standard and extended acess list?
what are the commands for extended and acess list? | HCL | 3 |
| Which command, that is used to test address configuration,
uses Time-To-Live (TTL) values to generate messages from
each router.
A. trace
B. ping
C. telnet
D. bootp | | 1 |
| Switching methods include cut-through, store and forward,
and a modified version of the first two methods. Which
statement about switching methods is true?
A. The store and forward method has low latency
B. The cut through method of switching has high latency
C. The modified version holds the packet in memory until 50
percent of the packet reaches the switch
D. The modified version holds the packet in memory until the
data spoon of the packet reaches the switch | | 3 |
| Identify the hardware component that stores the bootstrap
program?
A.) ROM
B.) NVRAM
C.) Booter load
D.) RAM
E.) Flash | | 2 |
| What utility can you use to see the path a packet takes
through an
internetwork?
A.) Route
B.) SNMP
C.) Trace
D.) Ping | | 2 |
| what is the need og
jitu(config)#ip helper address <ip address>
can any one exaplain it briefly
specially shain i am looking towards you.Becoz you are the
only one who can solve my that problem not even jitendera sinha | | 3 |
| Identify the access-list range for an extended IP access-list?
A.) 800 - 899
B.) 1 - 99
C.) 1000 - 1099
D.) 100 - 199 | | 4 |
| Identify 3 characteristics of a MAC address?
A.) Burned into the NIC
B.) 48 bits long
C.) Length is 32 bits
D.) Used to identify a host device
E.) Contains a network portion and a host portion | | 2 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 2 |
| The CSMA/CD Ethernet IEEE committee is defines as which of the
following?
A.) 802.2
B.) 802.3
C.) 802.4
D.) 802.5 | | 1 |
| Of the following characteristics, which apply to UDP?
Connection-oriented
Connectionless
Error checking
Low overhead
Best-effort delivery
| | 3 |
| Which protocol works at the Internet layer and is
responsible for
making routing decisions?
A.) UDP
B.) IP
C.) TCP
D.) ARP | | 2 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| ok this is practical senario question
how can we comunicate two diffrent network host by i single
1603 sires of cisco router rember that the cisco series of
that router have singe 100mbps ethernet
now think think
write all command
answer is so simple i wiil; give the answer after 20 visit
til then wait
| | 2 |
| Which information must a router know in order to perform
proper and pungent routing?
A. destination application of an incoming packet
B. number of other packets in a single flow of data
C. destination network address of an incoming packet
D. number of routers that also know a path to the destination | | 1 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 1 |
| What is proxy-ARP and how it is used and configured | | 1 |
| what is burst rate | ASD-Lab | 1 |
| Which of the following protocols are used to get an IP
address from a
known MAC address?
A.) BootP
B.) TCP
C.) IP
D.) ARP
E.) RARP
F.) ICMP | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
