| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| What is BGP Synchronization rules?? Can any one explain..??? | Hathway | 2 |
| Which command will enable CHAP authentication on a serial
interface that is using PPP?
A.) encapsulation chap
B.) ppp chap
C.) ppp enable chap
D.) ppp encapsulation chap
E.) ppp authentication chap
F.) ppp chap enable | | 2 |
| What are three benefits of Integrated Services Digital
Network (ISDN) (Choose three)
A. PVCs are faster and more reliable
B. No specialized equipment is required
C. Data transfer is faster than typical modems
D. Call setup is faster than with standard telephone service
E. It carries many types of data tramp such as voice video
and data | | 1 |
| In which three situations is a hold down timer reset?
(Choose three)
A. when the hold down timer expires
B. when infinity is finally defined as some maximum number
C. when the router exchanges update summaries at area borders
D. when the router detects faulty LSPs propagating through
the internetwork
E. when another update is received indicating a new route
with a better metric
F. when another update is received indicaing the original
route to the network has been restored
G. when the router receives a processing task proportional
to the number of links in the internetwork | | 1 |
| what is flow control,. | | 4 |
| Which ISDN protocol prefix specifies switching and signaling?
A.) I
B.) E
C.) Q
D.) S | | 1 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| what is farme realy.and on which layer it work | | 1 |
| Identify the 3 pieces of hardware you would not install to
prevent
broadcasts?
A.) Switch
B.) Repeater
C.) Bridge
D.) Router | | 2 |
| Identify the command to reload the router?
A.) Router(config)# reload
B.) Router# reset
C.) Router# reload
D.) Router> reload | | 1 |
| Identify the administrative distance and appropriate routing
protocol?
A.) RIP = 255, IGRP = 100
B.) RIP = 100, IGRP = 120
C.) RIP = 1, IGRP = 0
D.) RIP = 120, IGRP = 100 | | 3 |
| What are two ways IPX supports multiple logical networks on
an individual underrate? (Choose two)
A. network number
B. routing protocol
C. encapsulation type
D. autonomous system number | | 1 |
| Hi, All
I am configuring EIGRP in Packet tracer, after configuring
all the things it is not working but in one condition it is
working fine if i am putting all my router and network
withing one network subnets e.g. 172.16.0.0 or 10.0.0.0 but
whenever i am puting different network subnets e.g. in one
network it is RA(config-if)#=ip address 10.0.0.1, and in
fa0/0= 192.168.1.10 and in RB(config-if)#10.0.0.2 (s1/0) and
in S1/1 11.0.0.1 and in fa 0/0 192.168.100.1 ,where as in
third router RC(config-if)#=ip address 11.0.0.2 and in fa
0/0 172.16.1.10 and after configuring all this serial is
showing up and protocol showing up but eigrp process not
taking place after adding eigrp configuration, i tried with
"no auto-summary" command but not working.. Suggest me where
i missing something? can mail me at : gtech.innovator@gmail.com | | 18 |
| IP standard access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) port
C.) protocol
D.) source address | | 2 |
| A big part of the overhead on a network is broadcasts. You
divide a large number of hosts into smaller individual
networks and separate them with the proper device
According to proper networking terminology you have created
separate _______________________,
User Domains
Broadcast Domains
Collision Areas
Broadcast Areas
| | 1 |
| friends i have some problem in the acess list plz help me
out.
purbi sinha.
1 what is the diffrence b/w inbound and out bound access
list
2 what is main diffrence betwwen standred acesslist and
extended access list
3 where should i keep stnadred access list and exatended
access list i mean at which interface and why?
4 why wild card masking is used
5 what is switch febric in switching
plz help me out i am litle bit confuse
| | 1 |
| What is the function of the Transport layer and which protocols
reside
there?
A.) MAC addressing - IP
B.) Interhost communication - SQL, NFS
C.) Best effort Packet delivery - TCP, UDP
D.) End-to-end connections - TCP, UDP | | 1 |
| Identify 3 methods used to prevent routing loops?
A.) Split horizon
B.) Holddown timers
C.) Poison reverse
D.) SPF algorithm
E.) LSP's | | 2 |
| The two sublayers of the IEEE Data Link Layer are which of the
following?
A.) Link and Logical Control
B.) Data Link and LLC
C.) Logical Link Control and Media Access Control
D.) Data Link and MAC | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
