| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which command will copy the routers configuration from NVRAM
to a
Network file server?
A.) copy start tftp
B.) copy start tftp server
C.) copy tftp startup-config
D.) copy running-config tftp
E.) copy startup-config tftp | | 1 |
| Your PC has been configured with IP Address 192.168.3.25
and a subnet mask of 255.255.255.0. Which of the following
IP Addresses is a valid default gateway address for your
PC?
192.168.3.0 255.255.255.0
192.168.3.2 255.255.255.0
192.168.3.25 255.255.255.0
192.168.4.1 255.255.255.255
| | 1 |
| Identify 3 IP applications?
A.) AURP
B.) ARP
C.) Telnet
D.) SMTP
E.) DNS
F.) RARP | | 2 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| Which of the following use PVCs at layer 2?
A.) X.25
B.) HDLC
C.) Frame relay
D.) ISDN | | 1 |
| Can anyone explain the Split Horizon rule in RIP & also
Split Horizon with Poison reverse.
Jitu.... U knw wat i expect.. hehehehehe... | | 1 |
| Which memory component on a Cisco router contains the
dynamic system configuration?
ROM
NVRAM
Flash
RAM/DRAM | HCL | 16 |
| Identify the protocol to test connectivity without
configuring any
layer 3
protocols?
A.) TCP
B.) Ping
C.) IP
D.) CDP
E.) Telnet | | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| What is a key use of a device hardware address?
A. to obtain a vendor code / serial number from the user
B. to transmit a frame from one Interface to another Interface
C. to transmit a packet from one local device to another
local device
D. to transmit data from one local device to a remote device
across the internet
E. to contain logical information about the device to use
for end-to-end transmission | | 1 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Route# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| Your network uses a Class C address of 210.10.10.0. You
must now split up the network into separate shores to handle
multiple buildings separated by routers. Which two steps
must you take to determine the proper shored mask for your
networks? (Choose two)
A. determine the number of seperate networks required
B. determine how many devices will require DHCP addressing
C. determine the maximum number of hosts that will be on
each shored
D. determine the miniumum number of hosts that will be on
each shored
E. determine which router will be the IP default gateway for
each shored | | 1 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of the
connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| Whith the hierarchical numbering of IP addressing what
determines the spoon of the address that will identify the
network number?
A. subnet mask
B. dots between octets
C. class of the first octet
D. assignments of DHCP
E. address resolution process | | 1 |
| Identify 3 characteristics of IP RIP?
A.) Distance vector
B.) Administrative distance is 120
C.) Periodic updates every 60 seconds
D.) Uses a composite metric
E.) Can load balance | | 1 |
| You receive "input filter list is 800 and output filter list is
801" as part of the output from a show interfaces command.
What kind of
traffic are you filtering?
A. IPX/SPX
B. TCP/IP
C. LocalTalk
D. DDR | | 1 |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| Identify the 2 commands the saves the running-config to NVRAM?
A.) write memory
B.) copy running-config startup-config
C.) write network
D.) write backup | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
