| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is VLSM? how to Calculate VLSM? where it is use and
why? | | 4 |
| Which of these is the Private key?
A. Bear
B. Cave
C. Indian
D. Cowboy | | 1 |
| What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923 | | 1 |
| As a system administrator, you need to set up one Ethernet
interface on the Cisco router to allow for both sap and
Novell-ether encapsulations. Which set of commands will
accomplish this?
A. interface ethernet 0.1
ipx encapsulation Novell-ether
ipx network 9e
interface ethernet 0.2
ipx network 6c
B. interface ethernet 0
ipx encapsulation Novell-ether
ipx network 9e
interface ethernet 0
ipx encapsulation sap
ipx network 6c
C. interface ethernet 0.1
ipx encapsulation Novell-ether
interface ethernet 0.2
ipx encapsulation sap
D. interface ethernet 0.1
ipx encapsulation Novell-ether
ipx network 9e
interface ethernet 0.2
ipx encapsulation sap
ipx network 6c | | 1 |
| Identify the 2 commands that will display the status and
information about interface E0 only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface | | 1 |
| The following is partial output from a routing table ;
'192.168.10.0 [100/1300] via 10.1.0.1, 00:00:23, Ethernet1'
Which routing protocol is being used? (assuming defaults
have not been
changed)
A.) OSPF
B.) RIP
C.) BGP
D.) IGRP | | 1 |
| Which commands will restart the router?
A.) router#system exit
B.) router >reload
C.) router#shutdown
D.) router#reload
E.) router#(config)reload
F.) router#system restart | | 6 |
| Which command would show all Ethernet interfaces with IPX
configured on them?
A.) show interface ipx ethernet
B.) show ipx interface
C.) show ipx interface ethernet
D.) show ipx
E.) show version
F.) show run | | 1 |
| Which of the following are Distant Vector protocols?
A.) IGRP
B.) RIP
C.) OSFP
D.) EIGRP | | 1 |
| Which of the following is used to manage and monitor the
network?
A.) SNMP
B.) HTTP
C.) IP
D.) FTP | | 1 |
| Put the following steps of encapsulation into the correct order:
1) The data is broken into segments to be organized
2) Frames are converted to 1s and 0s to be put on the wire
3) Packets are converted into frames
4) Information that users enter is converted into data
5) The segments are changed to packets to be routed
A.) 4, 1, 3, 2, 5
B.) 4, 5, 1, 3, 2
C.) 2, 3, 1, 4, 5
D.) 4, 1, 5, 3, 2 | | 1 |
| What is the juncture at which the CPE ends and the local loop
portion of the service begins?
A. Demarc
B. CO
C. Local loop
D. Last-mile | | 1 |
| How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing | | 2 |
| Identify the type of hardware required to connect a Token ring
network to
an Ethernet network?
A.) Repeater
B.) TR-Enet
C.) Router
D.) Token Ring to Ethernet translation hub | | 1 |
| What is the default routing metric used by IGRP?
A.) MTU, delay, bandwidth, reliability, and loading
B.) Count to infinity
C.) Bandwidth and delay
D.) Hop count | | 2 |
| When using TCP, after a session is open, the applications
can adjust the amount of segments they receive before
sending an acknowledgment. This behaviour is known as
______________.
FCS
Windowing
MTU adjustment
Flexible Send Path
| | 1 |
| Which layer is responsible for negotiating data transfer syntax?
A.) Network
B.) Session
C.) Application
D.) Transport
E.) Presentation | | 1 |
| Which of the following are logged when IP access list logging is
enabled?
A.) source address
B.) protocol
C.) source port
D.) destination address
E.) access list number
F.) destination port | | 1 |
| Which OSI Reference Layer is concerned with path determination?
A.) Datalink
B.) Physical
C.) Network
D.) Transport
E.) Session | | 2 |
| Company XYZ has an employee that works out of the home. The
employee runs big client server applications and must
quickly transfer large files. The company wants the best
cost/benefit on this connection. What would be the most
practical solution?
A. an ISDN Basic Rate Interface (BRI) connection to the user
at home
B. a dedicated T1 connection to the user at home
C. a dedicated Frame Relay connection to the user at home.
D. a standard 28.8 analog dialup connection to the user at home. | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
