| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what is the difference between dynamic NAT and NAT
overload ? and how it works ?
| | 4 |
| Hi, I have packet tracer 5.0. I want to test intervlan
routing routing. Can someone plz tell me about intervlan
routing? | | 1 |
| What is the result of using a hierarchical addressing framework?
A. increased availability of addresses
B. decreased distance between routers
C. increased router memory requirements
D. no need to maintain routing information | | 1 |
| What is an advantage of LAN segmentation?
A.) Increases broadcasts.
B.) Increases collisions.
C.) Provides more protocol support.
D.) Decreases broadcasts.
E.) Routing protocol support. | Wipro | 2 |
| Identify the command to display the configured IP routing
protocols?
A.) show protocols
B.) show protocols all
C.) show routing-protocols
D.) show ip protocols | | 2 |
| Which type of switching reads in the entire frame before
forwarding it?
A.) Tabling
B.) Store-and-Forward
C.) Inverse ARP
D.) Fast Forward
E.) Cut-Through
F.) Routing | | 1 |
| Which layer is responsible for putting 1s and 0s into a logical
group?
A.) Session
B.) Application
C.) Transport
D.) Data Link
E.) Physical
F.) Network | | 1 |
| Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department | | 1 |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 4 |
| Which statement about the Committed Information Rate (CIP)
is true?
A. It is the rate in bits per second at which the Frame
Relay switch agrees to transfer data
B. It is the clock speed (pod speed) of the connection
(local loop) to the Frame Relay cloud
C. It is the maximum number of bits that switch can
transferduring any Committed Rate Measurement Interval
D. It is a signaling standard between the 3PE device and FP
switch. It is responsible for managing the connection and
maintaining status between the devices. | | 1 |
| Which IP Address Class is INCORRECTLY paired with its range
of network numbers?
A. Class A addresses include 192.0.0.0 through 223.255.255.0
B. Class A addresses include 1.0.0.0 through 126.0.0.0
C. Class B addresses include 128.0.0.0 through 191.255.0.0
D. Class C addresses include 192.0.0.0 through 223.255.255.0
E. Class D addresses include 224.0.0.0 through 239.255.255.0 | | 3 |
| Which Standard IP Access list commands will deny only the source
address 1.1.1.1?
A.) access-list 9 deny host 1.1.1.1
B.) access-list 9 deny 1.1.1.1 255.255.255.0
C.) access-list 9 deny 1.1.1.1 0.0.0.0
D.) access-list 9 deny 1.1.1.1 0.255.255.255
E.) access-list 9 deny 1.1.1.1 255.255.255.255 | | 2 |
| Which OSI Reference Layer controls end-to-end (host to host)
communication?
A.) Transport
B.) Physical
C.) Datalink
D.) Network
E.) Session | | 1 |
| Which layer defines the physical topology?
A.) Application
B.) Transport
C.) Network
D.) Data Link
E.) Physical
F.) Session | | 1 |
| Request any body to explain the parameters of Ipsec vpn
tunnel while creating a tunnel in Cisco ASA. | HCL | 3 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| What is the command to allow you to type Tokyo instead of the IP
address 172.16.30.1 to access a router named Tokyo?
A.) config t, ip host Tokyo 172.16.30.1
B.) config t, ip hostname Tokyo 172.16.30.1
C.) config t, hostname Tokyo 172.16.30.1
D.) config t, ip hostname 172.16.30.1 Tokyo | | 1 |
| what is route aggregation | | 2 |
| Identify IPX SAP and it's purpose?
A.) Sonet Access Pipe - interface to Sonet ring
B.) Service Advertising Protocol - advertise services
C.) Server Appletalk Protocol - appletalk directory services
D.) Service Access Point - identify upper layer protocols | | 1 |
| In the setup dialog, what do the square brackets indicate?
A. current or default spores
B. hard coded values that cannot be modified
C. values entered by the administrator but not saved
D. values that must be written to NVRAM before becoming enabled | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
