ALLInterview.com :: Home Page KalAajKal.com
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
tip       Ask Questions on ANYTHING, that arise in your Daily Life at     FORUM9.COM
Google
 
Categories  >>  Certifications  >>  Cisco Certifications  >>  CCNA
 
 


 

 
 CCNA interview questions  CCNA Interview Questions
 CCDA interview questions  CCDA Interview Questions
Question
How would you configure one host name that points to two IP

addresses?

A. IP host jacob 1.0.0.5 2.0.0.8

B. IP jacob 1.0.0.5 2.0.0.8

C. IP host jacob 1.0.0.5

D. IP host duplicate "all"
 Question Submitted By :: Guest
I also faced this Question!!     Rank Answer Posted By  
 
  Re: How would you configure one host name that points to two IP addresses? A. IP host jacob 1.0.0.5 2.0.0.8 B. IP jacob 1.0.0.5 2.0.0.8 C. IP host jacob 1.0.0.5 D. IP host duplicate "all"
Answer
# 1
Answer: A

The correct syntax is IP host name [

TCP-port-number ] address [ address ]..... So, "IP host

P1R1 1.0.0.5 2.0.0.8" is the correct choice. "IP host jacob

1.0.0.5" only points the host name jacob to one IP

address--1.0.0.5.
 
Is This Answer Correct ?    0 Yes 0 No
Guest
 

 
 
 
Other CCNA Interview Questions
 
  Question Asked @ Answers
 
WAN stands for which of the following? A.) Wide Arena Network B.) World Area Network C.) Wide Area News D.) Wide Area Network  1
Identify the hardware component that stores the bootstrap program? A.) ROM B.) NVRAM C.) Booter load D.) RAM E.) Flash  2
Which network mask should you place on a Class C address to accommodate a user requirement of two subnetworks with a maxximum of 35 hosts on each networks A. 255.255.255.192 B. 255.255.255.224 C. 255.255.255.240 D. 255.255.255.248  4
When determining whether or not to route a LAN segment, which rule of thumb do you use? A.) 60/40 B.) 50/50 C.) 80/20 D.) 90/10 E.) 70/30  1
What is the maximum hop count for Link-State protocols? A.) 15 B.) there is no hop count limit C.) 256 D.) 16  1
Identify 2 reasons for disabling CDP? A.) If the router is not configured for RIP B.) Save bandwidth by eliminating overhead C.) If the router is configured for Appletalk D.) When connected to a non-Cisco router  1
Cisco routers can secure the enable password with a one-way hash algorithm. What command would encrypt the enable password with the strong encryption method? A.) enable encrypt john B.) password john C.) enable secret john D.) enable password john E.) secret john F.) enable password 5 john  1
What is the administrative distance for IGRP? A.) 90 B.) 120 C.) 110 D.) 100  2
Which is true regarding half duplex Ethernet operation? A.) Half Duplex ethernet technology provides a transmit circuit connection wired directly to the receiver circuit at the other end B.) Half duplex transmission between stations is achieved by using point to multipoint Ethernet and Fast Ethernet C.) With Half Duplex transmission logically circuits feed into a single cable creating a situation similar to a one way bridge D.) Half Duplex transmission between stations is achieved using Point to Point Ethernet & Fast Ethernet  1
Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config  1
Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0  2
Identify 3 characteristics regarding CDP? A.) On by default B.) Shows only directly connected neighbors C.) Requires IP or IPX D.) 60 second update interval by default E.) 30 second updates interval by default  1
Identify the OSI layer responsible for end-to-end connections? A.) Network B.) Transport C.) Session D.) Data link E.) TCP  1
Which OSI Reference Layer is concerned with path determination? A.) Datalink B.) Physical C.) Network D.) Transport E.) Session  2
Which IP Address Class can have 16 million subnets but support 254 hosts? A. Class C B. Class A C. Class B D. Class D  3
there is three mode of vtp let there are three switch s1 in server mode s2 in transparent mede and s3 in clint mode then will that tranparnt mode going to effect the network if yes then how and if no then what it will do IBM1
How do you disable advanced editing? A.) terminal editing B.) terminal no editing C.) disable editing D.) no terminal editing  2
Which layer is responsible for negotiating data transfer syntax? A.) Network B.) Session C.) Application D.) Transport E.) Presentation  1
Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route  1
You want a message to be displayed every time someone tries to log on to the router. Which command is required to accomplish this task? A.) motd#(message)# B.) banner motd(message) C.) banner motd#(message)# D.) banner motd*(message) E.) banner login#(message)#  1
 
For more CCNA Interview Questions Click Here 
 
 
 
 
 
   
Copyright Policy  |  Terms of Service  |  Help  |  Site Map 1  |  Articles  |  Site Map  |   Site Map  |  Contact Us interview questions urls   External Links 
   
Copyright © 2007  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  Forum9.com   ::  KalAajKal.com