ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Certifications >> Cisco Certifications >> CCNA
 
 


 

 
 CCNA interview questions  CCNA Interview Questions (1883)
 CCDA interview questions  CCDA Interview Questions (88)
Question
What does the command "IP name-server 255.255.255.255"

accomplish?

A. It sets the domain name lookup to be a local broadcast.

B. This is an illegal command.

C. It disables domain name lookup.

D. The command is now defunct and has been replaced by "IP

server-name ip any"
 Question Submitted By :: CCNA
I also faced this Question!!     Answer Posted By  
 
Answer
# 1
Answer: A

By default DNS is enabled on a router with a

server address of 255.255.255.255, which provides for a

local broadcast.
 
Is This Answer Correct ?    20 Yes 2 No
Guest
 

 
 
 
Other CCNA Interview Questions
 
  Question Asked @ Answers
 
Identify the command to display the Frame Relay map table? A.) Router# display frame-relay map B.) Router# show frame-relay map C.) Router(setup)# show frame-relay map D.) Router# show map frame-relay   1
What is the 5-4-3-2-1 rule of network design?   3
You are given the IP address of 172.16.2.160 with a subnet mask of 255.255.0.0. What is the network address in binary? A. 10101100 00010000 B. 00000010 10100000 C. 10101100 00000000 D. 11100000 11110000   2
Identify the 2 methods to modify the routers boot sequence? A.) Setup program B.) Boot system commands C.) RXBoot D.) Config-register   1
Which of the following are valid Cisco encapsulation type names? A.) arpa = IPX Ethernet B.) novell-ether = IPX Ethernet_802.3 C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring D.) novell-fddi = IPX Fddi_Raw E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring F.) hdlc = HDLC on serial interfaces   1
here is your question sahin Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP. I knew about it from ICND 2 cisco press book. Three more questions - a) If we change the K value (I mean metric weight)on a router what will happen??? b) When redistribution is necessary in EIGRP. Is there any condition for that??? c) What is reference bandwidth for metric calculation in EIGRP. As we know, in OSPF, on a CISCO router reference bandwidth is 10Mbps.   3
How often does IP RIP send out routing table updates by default? A.) They send complete updates every 30 seconds B.) They send partial updates every 30 seconds C.) They send complete updates every 60 seconds D.) They send partial updates every 60 seconds   2
Which of the following can reply to a Novell Get Nearest Server (GNS) request? A.) Local Novell server B.) Remote Novell Printer C.) Cisco router D.) Novell client   1
Identify the purpose of the wildcard mask? A.) Match a certain portion of the IP address while ignoring the rest of the address B.) Determine the class of the IP address C.) Determine the network portion of an IP address D.) Hide the host portion of an IP address   3
What is convergence time? A.) The update time B.) The time it takes to reload a router C.) The time it takes for a packet to reach its destination D.) The time is takes for all routers update their tables after a change takes place   2
Identify 2 features of X.25? A.) Supports only IP B.) Utilizes switched and permanent virtual circuits C.) Contains minimal flow control and error recovery D.) Utilizes LAPB as it's data-link protocol   1
Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..   6
 
For more CCNA Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright © 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com