| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| The two sublayers of the IEEE Data Link Layer are which of the
following?
A.) Link and Logical Control
B.) Data Link and LLC
C.) Logical Link Control and Media Access Control
D.) Data Link and MAC | | 2 |
| Novell IPX network addresses have two conferrable parts.
The network administrator specifies the IPX network number.
How is the node number determined?
A. It is the serial number of the given device
B. It is assigned as a lease by Novell DHCP
C. It is also set by the network administrator
D. It is usually the MAC address of one Interface
E. It is downloaded by Netware Core Protocol (NCP) | | 1 |
| What was the key reason the International Organization for
Standardization released the OSI model?
A. users could access network servers faster
B. different vendor networks could work with each other
C. the industry could create a standard for how computers work
D. network administrators could increase the overall speed
of their network | | 1 |
| ok this is practical senario question
how can we comunicate two diffrent network host by i single
1603 sires of cisco router rember that the cisco series of
that router have singe 100mbps ethernet
now think think
write all command
answer is so simple i wiil; give the answer after 20 visit
til then wait
| | 2 |
| Which Distance Vector characteristic can help to speed up
convergence?
A.) Triggered Updates.
B.) Split Horizon.
C.) Poison Reverse.
D.) Hold Down timers.
E.) Inverse ARP. | | 1 |
| Which of the following provide connection-oriented transport
to upper
layer protocols?
A.) SPX
B.) RIP
C.) NLSP
D.) NCP | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Identify the 2 methods to modify the routers boot sequence?
A.) Setup program
B.) Boot system commands
C.) RXBoot
D.) Config-register | | 1 |
| What is the correct command line syntax for configuring a
port on
a 7000 or 7500 series Cisco router with a VIP card?
A.) port
B.) port adapter/port
C.) You can't put a VIP card in a 7000 or 7500 router.
D.) slot/port-adapter/port
E.) slot/port
F.) slot | | 1 |
| How many subnets can be gained by subnetting 172.17.32.0/23
into a /27 mask, and how many usable
host addresses will there be per subnet? | | 8 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not a
the same time | | 2 |
| If configuring a Cisco router to connect to a non-Cisco router
across a
Frame Relay network, which encapsulation type would you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| Identify the 2 commands the saves the running-config to NVRAM?
A.) write memory
B.) copy running-config startup-config
C.) write network
D.) write backup | | 2 |
| how to troubleshoot when protocols is down and link is not
getting up | HCL | 5 |
| Identify the 2 commands that copies the configuration in
NVRAM to
RAM?
A.) copy backup-config running-config
B.) configure nvram
C.) copy startup-config running-config
D.) configure memory | | 2 |
| Which of the following is a valid extended IP access-list?
A.) router(config)# access-list 101 permit tcp host
172.16.30.0 any eq
21 log
B.) router# access-list 101 permit tcp host 172.16.30.0 any
eq 21 log
C.) router(config)# access-list 101 permit any any 172.16.30.0
D.) router(config)# access-list 101 permit ip host
172.16.30.0 any eq 21
log | | 2 |
| What's the default CDP holdtime in seconds for Cisco routers?
A.) 30 seconds
B.) 180 seconds
C.) 90 seconds
D.) 60 seconds | | 3 |
| When would you use ISDN?
A.) To connect LANs using POTS
B.) To support applications requiring voice, data, and video
C.) When you need a consistent and very high rate of data speed
D.) To connect to IBM mainframes | | 2 |
| Identify the type of hardware required to connect a Token ring
network to an Ethernet network?
A.) Repeater
B.) TR-Enet
C.) Router
D.) Token Ring to Ethernet translation hub | | 1 |
| what is 5-4-3 rule? | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
