| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| When determining whether or not to route a LAN segment,
which rule of
thumb do you use?
A.) 60/40
B.) 50/50
C.) 80/20
D.) 90/10
E.) 70/30 | | 1 |
| Of the following switching types, which one has the highest
latency?
A.) Cut-through
B.) None
C.) Store-and-forward
D.) Fragment Free | | 1 |
| What is true when creating static route?
A.) The mask parameter is optional
B.) The administrative distance is required
C.) The gateway parameter is required
D.) The administrative distance is optional | | 1 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| The administrator of a comapny needs to ensure that a web
server in
their network is accessible from the Internet. Since the
network uses private
addressing, this requires an IP-to-registered-address
mapping. The following
command is entered on the router:
router(config)# ip nat inside source static 192.168.2.1
198.18.1.254
After unsuccessful results from a ping to the Internet, the
administrator issues the
show ip nat translations command and the output is blank.
What could be the
problem with the NAT configuration for this mapping?
A. The keyword overload is missing from the command.
B. The administrator needs to define a NAT pool first.
C. An access list must be defined to create static NAT
translations.
D. The interfaces need to be configured for NAT. | | 4 |
| At which layer of the OSI model does the ping command operate?
A. session
B. network
C. transport
D. maintenance | jetking | 6 |
| what is the difference between dynamic NAT and NAT
overload ? and how it works ?
| | 4 |
| b Which protocol for PPP LCP (Link Control Protocol) performs a
challenge handshake?
A. CHAP
B. PAP
C. UDP
D. IPX | | 1 |
| Identify the 3 characteristics of IGRP?
A.) Uses hop count as a metric
B.) Supports multiple unequal paths
C.) Administrative distance is 100
D.) Configured with an Autonomous system number
E.) Link state | | 1 |
| Identify 3 characteristics of ISDN?
A.) Transports voice and data
B.) Transports voice only
C.) Support both BRI and PRI
D.) Runs over existing phone lines
E.) Same as X.25 | | 1 |
| What is convergence time?
A.) The update time
B.) The time it takes to reload a router
C.) The time it takes for a packet to reach its destination
D.) The time is takes for all routers update their tables
after a change
takes place | | 1 |
| Which of the following are Presentation Layer standards?
A.) JPEG and PICT
B.) MPEG and MIDI
C.) ASCII and EBCDIC
D.) NFS and SQL | | 1 |
| What is the syntax to add a banner to the Cisco router?
A.) motd banner #
B.) banner
C.) banner motd #
D.) banner # | | 1 |
| The Datalink layer works with which of the following:
A.) Packets
B.) Bits
C.) Globules
D.) Frames
E.) Segments | | 2 |
| Identify 3 UDP characteristics?
A.) Reliable communication protocol
B.) Applications that use UDP must incorporate reliability
C.) Connnection-less oriented
D.) Incorporates no handshaking | | 2 |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM | | 1 |
| What does the ping response & mean?
* A: unreachable
* B: congestion
* C: user interrupt
* D: unknown packet type
* E: lifetime exceeded
| | 2 |
| Define Poison Reverse?
A.) To prevent regular update messages from reinstating a
route that has
gone down
B.) Packets sent out that are not destined for a network go
to the
default network
C.) Information received on an interface cannot be sent back
out the
same interface
D.) When a network goes down, the router enters in its table
the number
16 to signify destination unreachable | Google | 1 |
| When a router knows the IP address, but does not know the MAC
address of
the device it wishes to contact, it uses the ARP (Address
resolution
protocol) to determine the MAC address. After it learns the
MAC address,
it stores this information in the ARP cache. What is the
command to view
the ARP cache?
A.) sh mac
B.) show cache
C.) show arp
D.) sh arp interfaces
E.) show ip cache | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
