| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the purpose of ICMP?
A.) Avoiding routing loops
B.) Send error and control messages
C.) Transporting routing updates
D.) Collision detection | | 2 |
| Dear Mr. JITENDERA KUAMR SINHA how are and how is your
family? Anyway can u send me your personal email address? | | 4 |
| What are the OSPF router rules???? | NIIT | 6 |
| Identify the command to configure the router to boot from an
alternate IOS located in flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe | | 1 |
| How we put NIC in promiscuous mode when using MS windows,
can any one tell me in detail | Cisco | 1 |
| Which statement about the data link connection identifier
(DLCI) is true?
A. It is a number that identifies a local virtual circuit in
a Frame Relay network
B. It is a signaling standard between the CIDE device and
the Frame Relay switch
C. It is the clock speed (pod speed) of the connection
(local loop) to the Frame Relay Cloud
D. It is the Maximum number of uncommitted bits that the
Frame Relay switch will attempt to transfer beyond the
Committed Information Rate (CIP) | | 2 |
| Hi Gyes, here is new question. can you provide answer of
following question
Like linux, can we windows as router?
If yes how can we able to do this, | | 2 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of the
connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Route# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Router# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| In the command "router igrp 109" what does 109 signify?
A. an autonomous system
B. any network number which the router is attached to
C. the allowable length of the routing table
D. the network socket number | | 1 |
| You are given the IP address of 172.16.2.160 with a subnet
mask of 255.255.0.0. What is the network address in binary?
A. 10101100 00010000
B. 00000010 10100000
C. 10101100 00000000
D. 11100000 11110000 | | 2 |
| Which command sets IGRP as the routing protocol for
autonomous system 100?
A. Router(config)#igrp 100
B. Router(config)#network 100
C. Router(config)#router igrp 100
D. Router(config)#enable igrp 100 | | 1 |
| What does 'P' mean when running a Trace?
A.) Good route
B.) Protocol unreachable
C.) Source Quench
D.) Destination unreachable | | 2 |
| Which command will enable CHAP authentication on a serial
interface that is using PPP?
A.) encapsulation chap
B.) ppp chap
C.) ppp enable chap
D.) ppp encapsulation chap
E.) ppp authentication chap
F.) ppp chap enable | | 2 |
| What utility can you use to see the path a packet takes
through an
internetwork?
A.) Route
B.) SNMP
C.) Trace
D.) Ping | | 2 |
| Explain usage of ICMP in IP routing | | 2 |
| IPX routing updates occur how often?
A.) Every 30 seconds
B.) Every 60 seconds
C.) Only as needed
D.) When the remote router asks for an update | | 1 |
| Which of the following protocols are used to get an IP address
from a known MAC address?
A.) BootP
B.) TCP
C.) IP
D.) ARP
E.) RARP
F.) ICMP | | 1 |
| What does the IPX maximum path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
