| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Switching methods include cut-through, store and forward,
and a modified version of the first two methods. Which
statement about switching methods is true?
A. The store and forward method has low latency
B. The cut through method of switching has high latency
C. The modified version holds the packet in memory until 50
percent of the packet reaches the switch
D. The modified version holds the packet in memory until the
data spoon of the packet reaches the switch | | 3 |
| What is the Difference between Switch and Bridge? | | 3 |
| How signalling can be explained in D channel of ISDN? | Tulip | 1 |
| What’s the default CDP holdtime in seconds for Cisco routers?
| | 2 |
| Which OSI layer provides mechanical, electrical & procedural
specifications for activating, maintaining physical link?
A.) Presentation
B.) Network
C.) Application
D.) Physical
E.) Transport
F.) Data-Link | | 1 |
| Which commands would assign and enable IPX on an interface ?
A.) enable netware
B.) enable novell-ether
C.) router#(config)ipx routing
D.) You must first enable IPX globally and then
assign the network number to the interface .
E.) enable ipx
F.) router#(config-if)ipx network 4a | | 1 |
| What is difference between standard and extended access-list | HCL | 8 |
| Which two statements are true? (Choose two)
A. Ethernet 802.3 utilizes a half duplex method for data
transfer
B. In a 100 MBS point to point connection a full duplex
connection can provide 400 Mbs of data transfer
C. Ethernet switches can use the full duplex mode to connect
multiple nodes on a single pod of a switch
D. Full duplex Ethernet takes advantage of UTP using one
pair for transmission and the other pair for reception | | 1 |
| Hi Jitendera, I need ur suggestion. I completed my CCNA
certification & also hving some sort of real time
experience. Now i m planning to do CCNP. Little bit
confusion is that whether it wud be better for me to go for
CCNP ya CCNA (Security). As off my goal is to reach CCIE
(Security & Switching/Routing). So tell me some solution of
my confusion yaar..!!!
Thanx & Regards
Shahin.. | | 1 |
| What is public and private ip address., explain? and also
explain the ip address range of both public and private?
and where we use that public and private ip address? | | 10 |
| Identify the command that configures the bandwidth to 56K?
A.) Router(config-if)# bandwidth 56000
B.) Router(config-if)# bandwidth 56k
C.) Router(config)# bandwidth 56
D.) Router(config-if)# bandwidth 56 | | 1 |
| Identify the following components of the IPX address
2e.0000.0065.ed43
A.) Not a valid IPX address
B.) Network = 2e, Subnet = 0000, Node = 0065.ed43
C.) Network = 2e.0000, Node = 0065.ed43
D.) Network = 2e, Node = 0000.0065.ed43 | | 1 |
| Identify the command to configure the IP address
172.16.100.5 255.255.255.0?
A.) Router(config-if)# ip address 172.16.100.5 255.255.255.0
B.) Router(config)# ip address 172.16.100.5
C.) Router# ip address 172.16.100.5 255.255.255.0
D.) Router(config)# ip address 172.16.100.5 255.255.255.0 | | 1 |
| Which of the following is True regarding passwords on a
Cisco router?
A. All passwords can be encrypted
B. All passwords can be entered using the set-up dialogue
C. A password can be set before a user can enter the
privileged mode
D. A password can be set for individual lines
E. TACACS or Radius password authentication can be used. | | 1 |
| What is the default LMI type for Cisco Routers that are using
Frame-Relay?
A.) Annex D
B.) Q933A
C.) Cisco
D.) IETF
E.) ARPA
F.) Anex A | | 2 |
| Identify 2 HDLC characteristics?
A.) Default serial encapsulation
B.) Open standard
C.) Supports Stacker compression
D.) Supports point-to-point and multipoint | | 1 |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Rotuer(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| What is the purpose of the DLCI?
A.) Identifies the remote routers
B.) Contained with a 802.2 frame for routing purposes
C.) Used with PPP during authentication
D.) Identifies the PVC in a Frame Relay network | | 1 |
| What key do you use to view the last command?
A.) Left Arrow
B.) Space Bar
C.) Up Arrow
D.) Right Arrow | | 2 |
| Which command listed below sets the banner message when someone
connects to the router?
A.) message #
B.) banner #
C.) login banner #
D.) description #
E.) login description #
F.) banner motd # | | 2 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
