To prevent Service Advertisements (SAPs) from flooding a network, Cisco

Advertise your Business Here

Refer this Site

Login | Sign Up


	Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff HERE

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

To prevent Service Advertisements (SAPs) from flooding a

network, Cisco routers do not forward them. How are

services advertised to other networks?

A. Each router builds its own SAP table and forwards that

every 60 seconds.

B. Each router assigns a service number and broadcasts

that.

C. SAPs aren't necessary with Cisco routers.

D. Cisco routers filter out all SAPs.

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: To prevent Service Advertisements (SAPs) from flooding a network, Cisco routers do not forward them. How are services advertised to other networks? A. Each router builds its own SAP table and forwards that every 60 seconds. B. Each router assigns a service number and broadcasts that. C. SAPs aren't necessary with Cisco routers. D. Cisco routers filter out all SAPs.

Answer
# 1

Answer:: A

Cisco routers build SAP tables and forward the

table every 60 seconds. All SAPs can't be filtered even

with 4.x since NDS and time synchronization uses SAPs.

Is This Answer Correct ?

0 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


Which two physical interfaces support PPP? (Choose two) A. Ethernet B. Token Ring C. Synchronous serial D. Asynchronous serial		1
Which layer is responsible for putting 1s and 0s into a logical group? A.) Session B.) Application C.) Transport D.) Data Link E.) Physical F.) Network		1
What is true when creating static route? A.) The mask parameter is optional B.) The administrative distance is required C.) The gateway parameter is required D.) The administrative distance is optional		1
Identify the command to configure the router for IGRP autonomous system 100? A.) Router(config)# router igrp 100 B.) Router> router igrp 100 C.) Router# router igrp 100 D.) Router(config)# router igrp	CMS	2
Identify 2 reasons for disabling CDP? A.) If the router is not configured for RIP B.) Save bandwidth by eliminating overhead C.) If the router is configured for Appletalk D.) When connected to a non-Cisco router		1
Why would you use static routing instead of dynamic routing? A.) When you want automatic updates of the routing tables B.) All the time C.) When you have very few routes and want to conserve bandwidth D.) When you have a gateway of last resort		1
You need to come up with a TCP/IP addressing scheme for your company. How many network IDs must you allow for when you define the subnet mask for the network? A.) One for each WAN link B.) One for each router interface C.) One for each NIC installed in each client D.) One for each subnet with hosts E.) One for each host ID		1
Of the following switching types, which one has the lowest latency? A.) Cut-through B.) Fragment Free C.) None D.) Store-and-forward		1
Which two statements about IP RIP are true? (Choose two) A. It limits hop counts to 31 B. It is a link state routing protocol C. It uses autonomous system numbers D. It is capable of load sharing over multiple paths E. It uses bandwidth as the metric for path selection F. It broadcasts updates every 30 seconds by default		1
Identify 2 features of PPP CHAP authentication? A.) Username and password is sent in clear text B.) Authentication messages are sent periodically during the connection C.) Less secure then PAP D.) Local router 'challenges' the remote router		1
What is an administrative distance of 0 mean? A.) 0 means unbelievable B.) 0 is for EIGRP C.) 0 is the default distance for directly connected networks D.) 0 means unreachable		1
Identify the command to configure DLCI 100 on an interface e0? A.) Router(config)# frame-relay local-dlci 100 B.) Router(config)# frame-relay local-dlci 100 int e0 C.) Router(config-if)# frame-relay local-dlci 100 D.) Router(config-if)# frame-relay local-dlci 100 int e0		1
Identify the command to display the Frame Relay map table? A.) Router# display frame-relay map B.) Router# show frame-relay map C.) Router(setup)# show frame-relay map D.) Router# show map frame-relay		1
what is burst rate	ASD-Lab	1
Novell NetWare has an Ethernet frame type called Ethernet_II. What is the matching Cisco command line keyword for this encapsulation method? A.) dix B.) sap C.) arpa D.) gns E.) snap F.) novell-ether		1
What is a characteristic of Store and Forward switches? A.) They forward the frame before it is completely read. B.) They work at wire speed. C.) They are the same a Cut-Through switching. D.) They read the entire frame and check CRC before forwarding. E.) They decrease latency.		1
Identify the command to reload the router? A.) Router(config)# reload B.) Router# reset C.) Router# reload D.) Router> reload		1
hi i have some difficulty plz reply as s0on as possible. 1 what is csma/cd(i know u are familer with that protocol) 2 what is the need for it and and 3 rd one in which i need help how to enable csma/cd at router or switches shain make it answer as sson as possibele and call me afetr reply thanks jitendera kuamr sinha		1
Which two statements about a bridge are true? (Choose two) A. A bridge floods multicasts B. A bridge floods broadcasts C. A bridge does not flood multicasts D. A bridge does not flood broadcasts		1
Which 2 commands shows the Cisco IOS filename? A.) show IOS B.) show ver C.) show flash D.) show mem E.) show NVRAM		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com