| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Sequence and acknowledgement numbers are used for?
A.) Layer transitioning
B.) Flow control
C.) Port number addressing
D.) Reliability | | 1 |
| What is the purpose of Split Horizon?
A.) It prevents the regular update messages from reinstating
a route that
has gone down
B.) Information received on an interface cannot be sent back
out the same
interface
C.) Informs all neighbor routers that two routes exist
D.) Tells the router the destination is unreachable | | 1 |
| Which memory component on a Cisco router contains the
dynamic system configuration?
ROM
NVRAM
Flash
RAM/DRAM | HCL | 16 |
| which portecol is faster
tcp
udp
spx | | 5 |
| In version 11.2 of the IOS, a Cisco router configured for
frame-relay can automatically detect the LMI type. What is
this known as?
A.) Psychic
B.) ESP
C.) Inverse ARP
D.) Hello
E.) Reverse ARP
F.) Autosense | | 1 |
| Identify the 2 hardware components used to manage and/or
configure
a router?
A.) Auxiliary port
B.) ROM port
C.) Management port
D.) Console port | | 1 |
| You want to enable both arpa and snap encapsulation on one
router interface. How do you do this?
A. The interface can handle multiple encapsulation types
with no extra configuration.
B. Assign two network numbers, one for each encapsulation
type.
C. Enable Novell-ether to run multiple encapsulation types.
D. Both arpa and snap are enabled by default so you don't
have to configure anything. | | 1 |
| Identify the 2 commands that display the clock rate
configured on
the serial0 interface?
A.) show serial0
B.) show interface serial0
C.) Show clock rate serial 0
D.) show controllers serial 0
E.) show running-config | | 1 |
| What is difference between standard and extended access-list | HCL | 8 |
| What are the two types of access lists that can be
configured on a
Cisco router?
A. Standard
B. Extended
C. Filtering
D. Packet | | 1 |
| When you cords an IP address on a place router which command
stale the IP processing on the interface?
A. ip enable
B. network ip-address
C. ip address ip-address subnet mask
D. the exit command from the enabled configuration
E. copy running-configuration to startup-configuration | | 3 |
| What type of switching creates variable latency through the
switch?
A.) Cut-Through
B.) Inverted
C.) Layer 4
D.) Multiplexed
E.) Store and Forward | | 1 |
| (1)what is "rtp" and how it work,
(2)what is diffrence between igrp and eigrp
(3)the slection prcedure of dr and bdr is depend open
(4)why frame really is called nbma
(5)what is ppp
(6) what is diffrence b/w tcp and udp
(7) how can we implement ospf protocall on any router
(8)whta is as nomber
(9)what is AD value
(10)what is the broadcast id,n/w id and number of vallid
host of the 255.255.255.128/25 195.168.10.10/25
(11) what is stub network
(12) what is contigues n/w
(13)on which type of router we can implement default routing
(14)what is diffrence b/w hub switch;switch router,
(15)what is v lan
(16)what is the diffrence b/w link sate protocal and
distance vector protocall
(17)what is synchoransh mode of data transfer and
asynchronash mode of data transfer
(18) question on lab,
belive me frnds there are 20 questions and 5 questions on
lab implimentaion.around 1.1/2 hour i was in interview room
and after givieng 17 right answera and 4 in lab i got
slected
try to give answer
if any difficulty or any prob plz email me on
jitenderasinha.it@gmail.com
if any one of you havae boson netsim plz also intimate me
| | 4 |
| Novell NetWare has an Ethernet frame type called
Ethernet_II. What
is the matching Cisco command line keyword for this
encapsulation method?
A.) dix
B.) sap
C.) arpa
D.) gns
E.) snap
F.) novell-ether | | 1 |
| What is the regional Telco office called, where the customers
local loop
terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| hi... i am usin packet tracer 5.0.. i hav connect two
routers A and B. A has 200.100.25.100 and 1.0.0.1 and router
B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1
and 1.0.0.2... now i want to route 200.100.25.100 and
200.10.50.100 usin rip.. i enable rip in both the routers...
but whn i give the command show ip route... i jus get this
Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA
- OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF
NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF
external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 -
IS-IS level-2, ia - IS-IS inter area * - candidate default,
U - per-user static route, o - ODR P - periodic downloaded
static route Gateway of last resort is not set A# so can
sombody tell me where i hav gone wrong...
thanku | | 4 |
| How does inter- VLAN communication take place?
A. It takes place through any Cisco router
B. It takes place through a Cisco router that can run ISL
C. It takes place through a router but this disables all the
router a security and filtering functionality for the VLANS
D. For nonroutable protocals (e.g. NetBeui) the router
provides communications between VLAN domains
E. Inter-VLAN communication is not possible because each
VLAN is a separate broadcast domain | | 3 |
| Which layer is responsible for framing?
A.) Application
B.) Data Link
C.) Physical
D.) Network
E.) Transport | | 2 |
| Port selection is done at which layer of OSI reference
model????? | | 3 |
| You have an IP host address of 201.222.5.121 and a subnet
mask of 255.255.255.248. What is the broadcast address?
A. 201.222.5.127
B. 201.222.5.120
C. 201.222.5.121
D. 201.222.5.122 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
