| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| UDP works at which layer of the DOD model?
A.) Internet
B.) Host-to-Host
C.) Transport
D.) Data Link | | 2 |
| Identify the 2 commands to copy a configuration from a TFTP
server
to RAM?
A.) configure network
B.) configure overwrite
C.) copy backup-config running-config
D.) copy tftp running-config | | 1 |
| What does the 'S' mean when looking at the routing table?
A.) Statically connected
B.) Directly connected
C.) Dynamically attached
D.) Shutdown route | | 2 |
| Identify 3 feature of access-lists?
A.) Implicit deny will deny any packets not matched
B.) Processed sequentially from bottom to top
C.) Processed sequentially from top to bottom
D.) If a packet is denied it would be tested against the
remaining
statements in the access-list
E.) Once a match is made the packet is either denied or
permitted
F.) Enabled on all interfaces by default | | 1 |
| Which OSI Reference Layer is concerned with logical addressing?
A.) Network
B.) Transport
C.) Datalink
D.) Physical
E.) Session | | 1 |
| Which statement about Ethernet networks is true?
A. The advantage of a full duplex is the ability to transmit
data over 111 cable
B. Full duplex Ethernet requires a point-to-point connection
when only two nodes are present
C. Ethernet switches can use full duplex mode to connect
multiple nodes to a single pod of a switch
D. Half duplex is a cut through packet processing method
that is vow fast little error correction Full duplex is a
store and forward method that is slower but has better error
correction | | 1 |
| Which of the following is a valid TCP/IP socket for an
Email connection?
101.34.2.125:25
00-00-03-1B-CA-6F:143
202.167.23.101:21
60.4:110
| | 1 |
| What is the purpose of the DLCI?
A.) Identifies the remote routers
B.) Contained with a 802.2 frame for routing purposes
C.) Used with PPP during authentication
D.) Identifies the PVC in a Frame Relay network | | 1 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 2 |
| Identify the 2 items that TCP and UDP share in common?
A.) Both use port numbers to identify upper level applications
B.) Operate at the Network layer
C.) Both are Transport protocols
D.) Both are reliable communications | | 1 |
| Which layer manages protocol access to the Network layer?
A.) Datalink - MAC Sublayer
B.) Datalink - LLC Sublayer
C.) Transport
D.) Session
E.) Network | | 1 |
| What does the acronym ARP stand for?
A.) Address Resolution Phase
B.) ARP Resolution Protocol
C.) Address Resolution Protocol
D.) Address Recall Protocol | | 1 |
| Which statement is true regarding Administrative distance?
A.) It is a metric
B.) Number of hops between two routers
C.) Trustworthiness of the routing information
D.) RIP Administrative distance is 100 | | 1 |
| Which protocol gets a hardware address from a known IP address?
A.) RARP
B.) TCP
C.) IP
D.) BootP
E.) ARP
F.) ICMP | | 1 |
| 'Show cdp neighbors detail' show the following 3 pieces of
information?
A.) Hardware platform
B.) Software version
C.) Same as 'show version' command
D.) Up to 1 address for each protocol
E.) Non-direct connected routers | | 1 |
| Which port numbers are used by TCP and UDP to set up
sessions with
other hosts?
A.) 1024 and above
B.) 6 and 17 respectively
C.) 1-25
D.) 6-17 | | 2 |
| Which of the following is an example of the Network Layer?
A.) TCP
B.) IP
C.) SQL
D.) Token Ring
E.) LLC | | 1 |
| What are characteristics of UDP
A. It is reliable and acknowledged
B. It is unreliable and acknowledged
C. It is reliable and unacknowledged
D. It is unreliable and unacknowledged | | 2 |
| Which can be logged by IPX extended access lists?
A.) source address
B.) protocol
C.) source socket
D.) access list number
E.) destination socket
F.) destination address | | 1 |
| Identify the command mode necessary to enter the extended ping
command?
A.) Router#
B.) Router>
C.) Router(config)#
D.) Router(ext-ping)# | | 3 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
