| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| How would you set the clock rate to 64K, on interface serial 0,
from the interface configuration mode?
A.) clock rate 64000
B.) bandwidth 64
C.) clock 64
D.) rate 64
E.) clock rate 64k
F.) clock rate 64 | | 1 |
| When you issue the command show version your router returns
"Configuration register is 0x0101" From where does the
router boot?
A. ROM
B. NVRAM
C. Flash
D. a TFTP server | | 1 |
| Identify 2 transport layer protocols?
A.) IP
B.) TCP
C.) CDP
D.) ARP
E.) UDP | | 1 |
| Write out a config to permit only the below MAC address
to pass traffic through a port on your switch.
in another way writhe a confrigation which permit only mac
address trfaic through a port of your switch | | 3 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of the
connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| How we put NIC in promiscuous mode when using MS windows,
can any one tell me in detail | Cisco | 1 |
| What is difference between standard and extended access-list | HCL | 8 |
| You have two Cisco routers setup back-to-back in a lab using
DTE/DCE cables. To which router would you add the clockrate
command?
A.) The serial port on the DCE router
B.) The Ethernet port on the DTE router
C.) The Ethernet port on the DCE router
D.) The serial port on the DTE router | TCS | 3 |
| Which layer defines bit synchronization?
A.) Application
B.) Network
C.) Transport
D.) Physical
E.) Session
F.) Session | | 1 |
| Which OSI layer establishes, maintains and terminates sessions
between hosts?
A.) Application
B.) Physical
C.) Data-Link
D.) Presentation
E.) Network
F.) Session | | 1 |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| Identify the default encapsulation on serial interfaces?
A.) ISDN
B.) HDLC
C.) SDLC
D.) Frame Relay
E.) PPP | | 1 |
| Identify the command that displays ethernet0/1 interface status?
A.) show interface ethernet0/1
B.) show interface ethernet e0/1
C.) show interface ethernet0.1
D.) show ethernet0/1 | | 3 |
| Identify the effect of Ctrl-Z?
A.) Exits back to privileged exec mode
B.) Disconnect from the router
C.) Abort the ping operation
D.) Exits privileged exec mode | | 2 |
| Which of the following is a connectionless protocol at the
Transport layer?
A.) UDP
B.) ARP
C.) ICMP
D.) RARP
E.) IP
F.) FTP | | 4 |
| What is the default IPX Ethernet encapsulation?
A.) SNAP
B.) Arpa
C.) 802.2
D.) Novell-Ether
E.) SAP | | 1 |
| Given the configuration example<HR>
<B>interface ethernet0
ipx network 4a
ipx access group 800 out
interface ethernet1
ipx network 3d
interface ethernet2
ipx network 5c
access list 800 permit 3d 4a</B><HR>
Which two actions result from implementing this
configuration? (Choose two)
A. IPX network 5c will not receive any traffic
B. Traffic from network 3d for network 4a will be forwarded
out e0
C. Traffic from network 4a for network 3d will be forwarded
out e0
D. Traffic from network 3d destined for network 4a will be
forwarded out e2
E. The access list is applied to an outgoing interface and
filters outbound traffic | | 1 |
| Ping uses which Internet layer protocol?
A.) RARP
B.) ICMP
C.) ARP
D.) FTP | | 2 |
| Identify 3 ways in which a router can be configured?
A.) TFTP
B.) Nvram
C.) Ping
D.) Console
E.) Trace | | 1 |
| Identify the command to configure the IP address 172.16.100.5
255.255.255.0?
A.) Router(config-if)# ip address 172.16.100.5 255.255.255.0
B.) Router(config)# ip address 172.16.100.5
C.) Router# ip address 172.16.100.5 255.255.255.0
D.) Router(config)# ip address 172.16.100.5 255.255.255.0 | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
