ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Electrical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3070)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3286)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13320)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2362)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (414)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (77)
 Bio Engineering interview questions  Bio Engineering Interview Questions (17)
 Metallurgy interview questions  Metallurgy Interview Questions (79)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (163)
 Instrumentation interview questions  Instrumentation Interview Questions (2374)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (106)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (43)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (75)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1195)
Question
In short transmission line,why does the receiving end 
voltage is less than sending end voltage?
 Question Submitted By :: Electrical-Engineering
I also faced this Question!!     Answer Posted By  
 
Answer
# 1
In short Transmission line capacitive effect is negligible
hence neglected.Only two Parameters i.e. Inductance n
Resistance is present in Ckt both r drop making agents thus
causing Vtg.drop n reduction in vtg at receiving end.
 
Is This Answer Correct ?    5 Yes 0 No
Asmita
 
Answer
# 2
R= PL/A
P-specific resistance of the conductor
L- Length of the conductor
A- area of the conductor

since length is directly proportional to resistance the
receiving end voltage is less
 
Is This Answer Correct ?    2 Yes 1 No
Samraj
 
 
 
Answer
# 3
because v=IR
THEN R INCREASE WITH INCREASE IN LENGTH.
 
Is This Answer Correct ?    1 Yes 4 No
Vvk
 
Answer
# 4
due to voltage drop in transmission lines..
 
Is This Answer Correct ?    0 Yes 4 No
Krish
 

 
 
 
Other Electrical Engineering Interview Questions
 
  Question Asked @ Answers
 
What will the effect on a motor designed at 60 HZ, and operated on 50 HZ ??   8
what is "pu" in electrical engg.   4
why induction motor always operate at lagging p.f.?   4
Why should The rating of 11 kV DO Fuse is in mulyiple of hundred(200 Amp. 40 Amp, etc) Ampere wheareses the its fuse elemnt has rating in just few Amp (< 12 Amp)? ( Is it jusy beacuse of factor of safty).   1
In how we connect watt meter for open & short circuit test of a single phase transformer. Sail 2
Is there any calculation to find unknwon(unferroled) phases R Y B in alternator,3 phase motor anybody shoot my problem. how can we notice this is the respective phase?   2
What is Procedure the procedure to select CT's & PT's in 66kV and above substation? BEL 2
we all know that in transformer, voltage and current are inversely related i.e. Vp/Vs= Is/Ip....so in standard CT..we have a ratio of 200/5...that means our voltage should increase by ratio of 40..althoug that is not the case...because that requires high insulation level.and pratically not feasible......can anybody clarify my ques.......thanx   2
How can we calculate the rating of a cable with formula? TATA 1
why DG neutral is earth? HP 4
why power factor occur only inductive load not in resistive ?   8
why an ideal voltage source has low internal resistance????   1
 
For more Electrical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com