| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the OSI layer responsible for end-to-end connections?
A.) Network
B.) Transport
C.) Session
D.) Data link
E.) TCP | | 1 |
| Identify 3 feature of access-lists?
A.) Implicit deny will deny any packets not matched
B.) Processed sequentially from bottom to top
C.) Processed sequentially from top to bottom
D.) If a packet is denied it would be tested against the
remaining
statements in the access-list
E.) Once a match is made the packet is either denied or
permitted
F.) Enabled on all interfaces by default | | 1 |
| How would you set the clock rate to 64K, on interface serial 0,
from the interface configuration mode?
A.) clock rate 64000
B.) bandwidth 64
C.) clock 64
D.) rate 64
E.) clock rate 64k
F.) clock rate 64 | | 1 |
| Which of the following protocols are used to get an IP address
from a known MAC address?
A.) BootP
B.) TCP
C.) IP
D.) ARP
E.) RARP
F.) ICMP | | 1 |
| What is the default encapsulation of Netware 3.12?
A.) Ethernet_II
B.) 802.5
C.) 802.2
D.) 802.3 | | 2 |
| what is the difference between
1 router and switch
2 router and hub
3 hub and switch
4 bridge and switch
| Hathway | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| Identify the 3 kinds of routes IGRP advertises?
A.) Interior
B.) Dynamic
C.) System
D.) Exterior | | 1 |
| Identify the following components of the IPX address
2e.0000.0065.ed43
A.) Not a valid IPX address
B.) Network = 2e, Subnet = 0000, Node = 0065.ed43
C.) Network = 2e.0000, Node = 0065.ed43
D.) Network = 2e, Node = 0000.0065.ed43 | | 1 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| You need to come up with a TCP/IP addressing scheme for your
company. Which two factors must you consider when you define
the subnet
mask for the network?
A.) The location of DHCP servers
B.) The volume of traffic on each subnet
C.) The number of subnets on the network
D.) The location of the default gateway
E.) The number of host IDs on each subnet | | 1 |
| Define Poison Reverse?
A.) To prevent regular update messages from reinstating a
route that has
gone down
B.) Packets sent out that are not destined for a network go
to the default
network
C.) Information received on an interface cannot be sent back
out the same
interface
D.) When a network goes down, that network is advertised with an
infinite metric | | 1 |
| Which layer of the 7 layer model is responsible for
representing the
application information between 2 different OS's? For
example, converting
ASCII to EBCIDIC.
A.) Transport
B.) Application
C.) Physical
D.) Session
E.) Presentation
F.) Network | | 2 |
| What utility can you use to see the path a packet takes
through an
internetwork?
A.) Route
B.) SNMP
C.) Trace
D.) Ping | | 1 |
| what is secure hand shake protocol | | 2 |
| What is the result of using a hierarchical addressing framework?
A. increased availability of addresses
B. decreased distance between routers
C. increased router memory requirements
D. no need to maintain routing information | | 2 |
| Which of the following are examples of the Datalink Layer?
A.) LLC
B.) SQL
C.) TCP
D.) Token Ring
E.) IP | | 2 |
| Write out a config to permit only the below MAC address
to pass traffic through a port on your switch.
mac-address 0005.1b00.5b58 | | 4 |
| If configuring a Cisco router to connect to a non-Cisco router
across a
Frame Relay network, which encapsulation type would you select?
A.) Q933a
B.) ISDN
C.) IETF
D.) CISCO
E.) ANSI | | 1 |
| hi... i am usin packet tracer 5.0.. i hav connect two
routers A and B. A has 200.100.25.100 and 1.0.0.1 and router
B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1
and 1.0.0.2... now i want to route 200.100.25.100 and
200.10.50.100 usin rip.. i enable rip in both the routers...
but whn i give the command show ip route... i jus get this
Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA
- OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF
NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF
external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 -
IS-IS level-2, ia - IS-IS inter area * - candidate default,
U - per-user static route, o - ODR P - periodic downloaded
static route Gateway of last resort is not set A# so can
sombody tell me where i hav gone wrong...
thanku | | 4 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
