CSMA/CD stand for which of the following?
A.) Carrier Sense, Multiple Access with Collision Detection
B.) Collision Sense, Multiple Access with Collision Detection
C.) Collision Sense, Multiple Access with Carrier Detection
D.) Carrier Sense, MAC address with Collision Detection
How often does IP RIP send out routing table updates by default?
A.) They send complete updates every 30 seconds
B.) They send partial updates every 30 seconds
C.) They send complete updates every 60 seconds
D.) They send partial updates every 60 seconds
CPE is an acronym for which of the following?
A.) Customer Premise Equipment
B.) Central Processing Engineering
C.) Customer Process Equipment
D.) Central Processing Equipment
IP extended access lists use which of the following as a
basis for
permitting or denying packets?
A.) destination address
B.) all of the above
C.) protocol
D.) source address
E.) port
What does the Spanning Tree Algorithm (STA) do?
A.) Restore lost frames
B.) Builds routing tables for routing through an internetwork
C.) Forward packets through a switch
D.) STA is implemented by STP to prevent loops
What parameter is used with statically assigned routers to tell
packets which interface to use to reach a distant network?
A.) Mask
B.) Subnet
C.) Default gateway
D.) Interface
What does the IPX maximum path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths)
What is true when creating static route?
A.) The mask parameter is optional
B.) The administrative distance is required
C.) The gateway parameter is required
D.) The administrative distance is optional
What is the default encapsulation and frame type on an Ethernet
interface when enabling Novell?
A.) SNAP
B.) Ethernet_II
C.) 802.2
D.) 802.3
E.) SAP
F.) Token_SNAP
hi friend i am stuck in the big problem.this problem is
regading pix firewall. i have a cisco pix 515e firewall
inmy company.now when i configure it and after rebooting it
the ACT link never getup.when i apply clear config all
comand the ACT link get up after oveservation i see that
there is fauilover problem
when i apply failover active ACT link agin get up
is there any way to get my firewall in standby mode
rember that there is only on firewall within my n/w
i am lookig towards all of you
jitendera kumar sinha
76
hi shain can u send me some detail about bgp so that i can
enhance my knowledge over bgp and can you also teach me
about the process of suppernating.
now what i am thinking that this could be last visit on that
site overhere.so please mail that short of thing on my gmail
id
i am requesting to all of the visitor that please send
theire doubt or question to my new gmail id which is
jitendera.ccnainterview@gmail.com.i will try to solve it if
i am capable to do it
Wishing all of you for great future
Jitendera kaumar sinha
25
can any budy send the steps for enabling snmp on cisco
switches(L2).
38
hi friend i am sending some interview question which is
asked from me at volvo hope this will help you of all
1 what is mpls
al question is posted by jitendera kumar sinha
Which IEEE standard is used to define Wi-Fi?
A. IEEE 802.3
B. IEEE 802.5
C. IEEE 802.11h
D. IEEE 802.11c
E. IEEE 802.11
3
Hi Jitendera, Wat do u do..?? I mean r u working
anywhere???? Basically where r u from??? If u don't hv any
problem, u can say..?? Or else mail me mr.shahin07@gmail.com
89
Can anyone explain in details port fast, uplink fast &
backbone fast features introduced by CISCO (The GOD FATHER
of NETWORKING.... Hehehehehe).