hi friend i am stuck in the big problem.this problem is
regading pix firewall. i have a cisco pix 515e firewall
inmy company.now when i configure it and after rebooting it
the ACT link never getup.when i apply clear config all
comand the ACT link get up after oveservation i see that
there is fauilover problem
when i apply failover active ACT link agin get up
is there any way to get my firewall in standby mode
rember that there is only on firewall within my n/w
i am lookig towards all of you
jitendera kumar sinha
how we can creat VPN..??? how it can be configured on cisco
switches..??? can we creat VPN on different networks..???
why we need to create VPN..??? kindly write complete
activity of commands to configure a VPN on switch..??? me
specially looking towards Jatendra and Shahin
ok this is practical senario question
how can we comunicate two diffrent network host by i single
1603 sires of cisco router rember that the cisco series of
that router have singe 100mbps ethernet
now think think
write all command
answer is so simple i wiil; give the answer after 20 visit
til then wait
Hi Guys
I am facing one problem while configuring PAP over Point to
Point links. Configuration scenario is like this.
ROUTER 1: (Hostname – R1)
R1(config)#username R2 password CCNA2
R1(config)#interface serial 1/1
R1(config-if)ip address 10.0.0.1 255.0.0.0
R1(config-if)#lock rate 64000
R1(config-if)#encapsulation ppp
R1(config-if)#ppp authentication pap
R1(config-if)#ppp pap sent –username R1 password CCNA1
R1(config-if)#no shutdown
ROUTER 2: (Hostname – R2)
R2(config)#usename R1 password CCNA1
R2(config)#interface serial 1/1
R2(config-if)#ip address 10.0.0.2 255.0.0.0
R2(config-if)#encapsulation ppp
R2(config-if)# ppp authentication pap
R2(config-if)# ppp pap sent –username R2 password CCNA2
R2(config-if)#no shutdown
Now problem is that, after configure the command “ppp
authentication pap” the “Line protocol” status goes down on
each router. But when I disable this command using “no ppp
authentication pap”, the “Line Protocol” status goes up.
What could be the problem, can anyone explain it plzzz….!!!
Thanks in Advance…!!
Shahin..
How to see the running-config & startup-config infor from
global configuration mode.
As we know, from priviledge mode we cn see it by executing
command. i.e.
Router#show running-config
and
Router#show startup-config
Now wat is the coommands use in global configuration mode o
see those info.
Router(Config)# ??????
You have OSPF traffic flooding your network
via one of your router interfaces. Write the access
list line that will deny all ospf traffic. Don't
worry about the other lines of the access list.
let there are three switch and there are 3 ree valn craed
on each switch that is vlan 2 on first switch valn 3 on 2nd
switch and vlan 4 is cretaed on switch 3
i have implemnted intervlan routin through ciso switchses.
the router is conected through its fa0/1 port by one switch
and and the two switch are trunked with each other
now question is that we want to comuniacte betwwen vlan but
does alse want that only vlan 2 is allow to access internet
(ISP)which is conected through s0 interface of router.and
no any vlan can access that internet.what should be
solution.
can any budy send the steps for enabling snmp on cisco
switches(L2).
40
hi friend i am stuck in the big problem.this problem is
regading pix firewall. i have a cisco pix 515e firewall
inmy company.now when i configure it and after rebooting it
the ACT link never getup.when i apply clear config all
comand the ACT link get up after oveservation i see that
there is fauilover problem
when i apply failover active ACT link agin get up
is there any way to get my firewall in standby mode
rember that there is only on firewall within my n/w
i am lookig towards all of you
jitendera kumar sinha
76
what is vtp
there is three question regatding vpn but i know it is not
conserned with that
from last ten days i watched that no any new questions are
placed in ccna catogarey.so plz place the questions it is
very use full to beginers like us
87
Can anyone explain in details port fast, uplink fast &
backbone fast features introduced by CISCO (The GOD FATHER
of NETWORKING.... Hehehehehe).
84
hi shain can u send me some detail about bgp so that i can
enhance my knowledge over bgp and can you also teach me
about the process of suppernating.
now what i am thinking that this could be last visit on that
site overhere.so please mail that short of thing on my gmail
id
i am requesting to all of the visitor that please send
theire doubt or question to my new gmail id which is
jitendera.ccnainterview@gmail.com.i will try to solve it if
i am capable to do it
Wishing all of you for great future
Jitendera kaumar sinha
27
hi friend i am sending some interview question which is
asked from me at volvo hope this will help you of all
1 what is mpls
al question is posted by jitendera kumar sinha
Hi Jitendera, Wat do u do..?? I mean r u working
anywhere???? Basically where r u from??? If u don't hv any
problem, u can say..?? Or else mail me mr.shahin07@gmail.com
To Refer this Site to Your Friends 
Site Map
