In which category should Frame Relay be placed within the
following Job Aid?
Name of Protocol Type of Protocol # of Users # of Hosts or
Servers Comments
When is the route to a node determined in an SRB (Source
Route Bridging) Token Ring network?
A. Before any data is transmitted
B. After the data is transmitted
C. During the transmission of data
D. After the first frame is transmitted
How does the Spanning Tree Protocol (STP) prevent bridging
loops?
A. By not allowing any redundant paths within the network
B. By calculating the metrics of each path
C. By detecting and logically blocking redundant paths from
the network
D. By creating virtual LANS
When designing a flat switched network you can have:
A. the same number of IP and IPX nodes without performance
degradation
B. more IP than IPX nodes on the same segment
C. more IPX than IP nodes on the same segment
D. more AppleTalk than IP nodes on the same segment
What are two services that DUAL (Diffusing Update Algorithm)
performs for EIGRP?
A. Provides loop-free operation throughout an entire route?s
computation
B. Simultaneous synchronization of routers involved in a
topology change
C. Updates the autonomous system number
D. Allows advertised distances to use feasible distances
What is the second step when creating a prototype?
A. Develop a test plan
B. Review the customer requirements
C. Investigate what the competition will be proposing
D. Define how big the prototype will be
When are SNMP traps sent?
A. When the SNMP manager wants to perform remote
configuration on a networking device
B. When an SNMP agent wants to inform the SNMP manager about
a change of state on the networking device
C. When the SNMP manager wants to access large chunks of data
D. When the NMS wants to share trap information
When doing an RFP (Request for Purchase) for a customer, at
what step do you reiterate your solution and the customer
requirements?
A. Design Requirements
B. Design Solution
C. Summary
D. Appendices
What network design is becoming common when there is a
central office with one or more remote locations?
A. ISDN PRI at the central location and ISDN BRI at the
remote locations.
B. Using core routers at all sites
C. Only using access routers
D. Using a full mesh network
hi shain can u send me some detail about bgp so that i can
enhance my knowledge over bgp and can you also teach me
about the process of suppernating.
now what i am thinking that this could be last visit on that
site overhere.so please mail that short of thing on my gmail
id
i am requesting to all of the visitor that please send
theire doubt or question to my new gmail id which is
jitendera.ccnainterview@gmail.com.i will try to solve it if
i am capable to do it
Wishing all of you for great future
Jitendera kaumar sinha
from last ten days i watched that no any new questions are
placed in ccna catogarey.so plz place the questions it is
very use full to beginers like us
87
hi friend i am stuck in the big problem.this problem is
regading pix firewall. i have a cisco pix 515e firewall
inmy company.now when i configure it and after rebooting it
the ACT link never getup.when i apply clear config all
comand the ACT link get up after oveservation i see that
there is fauilover problem
when i apply failover active ACT link agin get up
is there any way to get my firewall in standby mode
rember that there is only on firewall within my n/w
i am lookig towards all of you
jitendera kumar sinha
76
how many default route can be configure on a router
57
hi friend i am sending some interview question which is
asked from me at volvo hope this will help you of all
1 what is mpls
al question is posted by jitendera kumar sinha
Hi Jitendera, Wat do u do..?? I mean r u working
anywhere???? Basically where r u from??? If u don't hv any
problem, u can say..?? Or else mail me mr.shahin07@gmail.com
89
what is leased line and if any issue occur what will u do
thai is trouble shootin occurs let leased line is down
Site Map
